Recent content by RevelinoSuriname

Hi, I would like to create a Branch Office Tunnel between a NVR1100 and a BSR222. The NVR1100 has been discontinued but I thought it might still be available to create that BOT. On the side of the NVR1100 I have a Static public ip. The NVR1100 I would like to use as a responder. On the side of...

Will do...Thanks.

Hi, I would like to create a Branch Office Tunnel between a NVR1100 and a BSR222. The NVR1100 has been discontinued but I thought it might still be available to create that BOT. On the side of the NVR1100 I have a Static public ip. The NVR1100 I would like to use as a responder. On the side of...

Hi, I have a BSR222 at HQ configured to terminate ABOT tunnels coming from a remote location. This works fine. When I enable and configure the BSR222 at HQ to terminate user tunnels, the ABOT is not working anymore. Does anyone know if the BSR222 can support both ABOT's and user tunnels...

Hi HungryHouse, I tried everything showed in the document but still can't get it working. I replaced the AT initial string with one that should work with the modem. One thing I noticed is that the BSR222 sends out an ATH command which I think is wrong. And I am not able to change this anywhere...

Hi, I am in the process of implementing a Nortel BSR router and would like to configure the backup feature included with it. This will be usefull if the primary WAN link goes down. I see that I need to connect the BSR222 to an external modem which I have already done, but I am stuck at the...

tried with the D option. Connected a ethernet cable to a laptop. Installed a TFTP server on the laptop and placed the image on the TFTP server, but the switch can't download the file. I think that's just because the switch is not working and none of the ports are. Switch doesn't have a seperate...

Curtismo, Here is what I get when pressing S: ********************************************** Press 'a' to run Agent code Press 'd' to Download agent code Press 'e' to display Errors Press 'i' to Initialize config flash Press 'p' to run POST tests Press 'r' to Reset Press 's' to display...

see below what happens when selecting 2: Press 'a' to run Agent code Press 'd' to Download agent code Press 'e' to display Errors Press 'i' to Initialize config flash Press 'p' to run POST tests Press 'r' to Reset Press 's' to display System information Erase Flash: 1 - Config-1 2...

Hi DaddyOfThree, Thanks for your prompt response. I tried pressing the i command and get the following: *********** Erase Flash: 1 - Config-1 2 - Config-2 3 - Config Selector-2 Select [ <config-1> ]: Erase Flash? y/N [ N ]: n Press 'a' to run Agent code Press 'd' to Download agent code...

Hi, I have a Nortel BES 1010-48T switch here that will not boot. It does power up and all the fans are running. None of the lights in the front for the ethernet port are blinking. I tried to ping the switch on it's given IP adress but no response. I connected to the switch via serial and this is...

Hi, I am in the process of configuring some new Nortel BES1010 switches. I use both BEM and IE to manage the switch. I want to uplink the switches with fiber to another switch at another location but I am unsucessful in doing that. I use SX GBICs on the switches. I thought that maybe those ports...

Thanks DaddyOfThree. So I think the router to go with is the ERS 5500. Do you know what happened with the passport 1600 series? It's not being showed in the ERS portfolio: http://products.nortel.com/go/product_content.jsp?segId=0&parId=0&prod_id=29580&locale=en-US Is it MD?

Thanks for your reply DaddyOfThree. You mentioned IP Routing. Which entry or feature in the Q4 2007 feature list specifies that? I would like to figure out what entry level L3 switch from Nortel to select.

Hi, Is the ERS2500 series switch a real router? (L3 switch?). I want to route traffic between 5 subnets and looking for the smallest Nortel router that would be able to do the job. Thanks in advance.