Recent content by redwolf52

I just passed my 640-801 and wanted to get some advice on going after the CCDA. I have heard that if you can pass the CCNA you are pretty close to being able to pass the CCDA. Is this true and what study materials are good for CCDA. Or should I scrap design and start on CCNP? thanks in advance

This is hard not having the ability to lay hands on the router but the tech is copying down the configs and sending them to me. He ran sh ip route and got Gateway of last resort is not set I am going to have him change the static route to the serial interface and try again. thanks

well bringing up the interface was correct as was removing the no ip routing command, but the tech still cant ping past the wan interface. Here is a copy of the running config. Let me know if you see anything Building configuration... Current configuration : 2164 bytes ! version 12.2...

Here is the console output from a power on. 00:00:06: SERVICE_MODULE(Serial1/0): self test finished: Passed 00:00:09: %LINK-3-UPDOWN: Interface Serial1/0, changed state to down 00:00:10: %LINK-3-UPDOWN: Interface Ethernet1/0, changed state to up 00:00:10: %SYS-5-CONFIG_I: Configured from memory...

I have created the same config on the new 3620 but when I plug in the T1 link the interface dosent come up. Does my ISP have to clear some arp cache or some other cache for me to switch routers? Basic config, static route to my isp and same encapsulation as on the old router. When I plug the...

found the problem according to cisco TAC the image was too big for RAM, it was compressed enough to fit on the 32 meg of flash but when it de-compressed it was too big to load all of it into ram so it just hung. tried a smaller image and had no problems thanks for your help

ok new problem. I finally got the image uploaded to the router and I went in and changed the confreg back to 0x2102 and rebooted and now I get System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) C3600 processor with 32768 Kbytes of main memory Main memory is...

yeah i dont think there is an image to begin with. This is the first "new" router I have worked on. I am now pushing an ios image to it thru xmodem. Is that the preferred way to push a first time image to a router? thanks

I am setting up a new 3620 router and i cant get it to boot to the initial configuration. It keeps boothing to the rommon prompt. I have changed the confreg 0x2142 and back to 0x2102 and i get the same results. any ideas? thanks in advance

I am setting up a new router and everytime I boot it, it goes to the rommon prompt. I never am asked to enter initial configuration. I have changed the confreg 0x2142 and back to 0x2102 but still get the rommon prompt. what am i missing? btw its a cisco 3620 router thanks in advance

I just bought the new Sybex book yesterday. I will let you guys know how it is.

I kep getting this error The maximum amount of time for a script to execute was exceeded. You can change this limit by specifying a new value for the property Server.ScriptTimeout. Any ideas where I go to up the Server.ScriptTimeout value? Thanks

I have been studying using the CCNA Exam #640-507 Sertification Guide, it appears that it is really behind the current test. What would you recommend as THE book to read before taking this test.The 507 book is full of IPX so I dont want to waste time studying that and miss out on other material...

How many total questions is the test? and any idea on the amount of IPX? Thanks

Do you get the use of a calculator for the subnetting secions of the CCNA? I have been studying off and on for about 4 months and I feel like Im in good shape for everything except the subnetting. I need to cram again because I keep having to re teach myself. If I can use a calculator Im in...