Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by reddevil2

  1. reddevil2

    ICND 2 CCNA

    Thanks lerdalt will try when I have revised a bit more M Steele Network+ CCENT
  2. reddevil2

    ICND 2 CCNA

    thanks I am probably mistaken but I had a code to resit the CCENT when I failed that one. M Steele Network+ CCENT
  3. reddevil2

    ICND 2 CCNA

    Where can I get a free resit code for thie ICND 2 CCNA exam?? M Steele Network+ CCENT
  4. reddevil2

    Setting Laptop IP

    Hi Guys I would like to apologise for the earlier question, I was having a bad day where things just got ontop of me. My memory went blank and I panicked. Sorry. I'll try to mellow out before I get to that stage again. M Steele Network+ CCENT
  5. reddevil2

    Setting Laptop IP

    Shouild I give up because I don't understand how to do certain things???? Or can I learn them as I go. Maybe I should just be a paper whatever with the CCENT I hold, and forget the CCNA. I was thinking of looking at the SMBEN course maybe I should forget that aswell???? M Steele Network+ CCENT
  6. reddevil2

    Setting Laptop IP

    Hi Guys How do I set the IP address on the laptop that I am using to configure my Cisco home lab? M Steele Network+ CCENT
  7. reddevil2

    VLSM

    Hi Guys I probably missed the forum on this but here goes anyway. For VLSM if I have a IP Addressing Scheme of 192.168.1.0/24 and I need to block it into a 97and 45. Which way would I go about it. Would the 97 be a/25 notation and the 45 a /26, and wouldn't this waste address space??? M Steele...
  8. reddevil2

    Cisco LAB switches

    Hi Guys I have a CISCO LAB at home that comprises of three routers, 2x 2503 and 1x 2610, I ahve set the clockrate on 1x 2503 routers and set all IP's and can ping one from the other, since receiving guidance from one or many of you in the routing forum. My problem is in my LAB I have two...
  9. reddevil2

    CISCO CLI

    If I plugged the ethernet cable from my cable modem into one of my lab routers, which one would I plug into?? Would my router then not receive an IP Address from the DHCP pool at my ISP?? M Steele Network+ CCENT
  10. reddevil2

    CISCO CLI

    Hi I have changed the confreg to 0x2102, but still cannot seem to ping from my 2610 to the second 2503, the first 2503 I have has been set with the clock rate for the other two, I have IP addressed both serial links on this router. int s0 192.168.1.1/30 int s1 192.168.2.1/30 On the 2610 I have...
  11. reddevil2

    CISCO CLI

    How do I return to 0x2012 configuration from 0x2142, without losing the configuration I have entered. I can ping from the main centre router which my clocking router in my lab to the other two, but cannot ping the routers on either side of it. Is it because of the 0x2142 configuration is on my...
  12. reddevil2

    Cisco 2610 'Password Recovery is Disabled'

    I have a 2500 series router, how do I clear the previously configured memory to start again, as I cannot remeber the access password??? M Steele Network+ CCENT
  13. reddevil2

    Break into Cisco Networking.

    Unlike Giant99 I don't have my full CCNA yet just the CCENT, do good at the IV stage, only to be rejected on the lack of exoeriece points later on. I have just bought a lab off EBAY. cost £215 with postage. It is not up and running yet but I feel the more I'll gat time to get things wrong at...
  14. reddevil2

    CCNA LAB

    Thanks for all the advice, downloaded a copy of that book as soon as I was given the link, all I need now is to get a power source and a place to place my little stack of cisco gear. But that will come in time. Thought I had lost everything again yesterday, when I downloaded reccommended...
  15. reddevil2

    CCNA LAB

    CISCOGUY33 2610 router has WIC 2A/S serial card, I have two CentreCOM 210T twisted pair transceiver,IEEE 802.3 10 BASE T that came with the lab. I have three straight through, three cross over two DCE-DTE cables, and a rollover cable which also came with the lab
See more

Part and Inventory Search

Back
Top