Recent content by rcarpent

Hi to All I am running Arcserve 11.5 SP3 on a redhat linux 4 update 7 server. The server is a DL380 G4. The tape drive being used is a Adic Suploader 3 (Ultrium 4) Drive. Tape is a Imation 800/1.6 TB. All appear to be OK, We have one interface thats assigned to be used by oracle and thats...

Hi All In the process of trying to do a recovery. I am on Arcserve 11.5 SP3 for linux. Redhat 4 is the backup server. We are tring to do a restore and getting the following error. I am unable to get any where with CA at the moment. We backup with no problems Solaris / Intel / HPUX. I am...

I am using CA BrightStor ARCserv backup for linux 11.5 SP3 installed on a Redhat As4 server. From the GUI when I try to back up all clients. I have 30. I get a prompt for each client to enter the root password. How can I get around that I would like to not have to enter the password. Thanks in...

I am using BrightStor ARCserv Backup for Linux Release 11.5 SP 3 (Build 2427). Linux Version Redhat 4.0. Tape drive being used is Adic Faststor 2 Lto2. The question I have is when running a backup or after a backup has completed. Is how to tell what capacity has been used on tape? I am from a...

Configuration Software: BrightStor Arcserve Backup for Linux 11.5 SP2 Hardware: 2 ADIC FastStor 8 slot labries connected to one Dual controller. Controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07) The goal to run 2 full backups at the same time to each...

I am running Networker 7.2.2 Build 494 on HP DL380 Server rennung Redhat AS 3 Update 5. I am backing up around 500GB. I run Daily full backups. It seams like I need to stop and start networker after each backup other wise I get a networker server crash in the middle of the backup. If I run...

I have an Faststor-2 tape library (8 Slots) connected to a Adaptec 29320-ALPR Redhat kernel 2.6.9-5.ELsmp Intel server. Looking to run Networker 7.2.2. So far I have installed Redhat version 4.0 (2.6.9-5.ELsmp)Base (No patches at this point) I install the recommended driver for the Adaptec...

Are you using the SMP kernel. If not switch to the SMP kernel. # grep -i memtotal /proc/meminfo MemTotal: 5907480 kB Linux contact 2.4.21-32.0.1.ELsmp #1 SMP Tue May 17 17:52:23 EDT 2005 i686 i686x I am able to use the memory. Boot off the SMC kernel and check the memory again.

Thanks I did a search and got the performance link. Thanks

Thanks for this hint. What is bigasm ?? I am new to networker

HI all I am using Networker 7.2.2 Build 422 on a Linux AS 3.0 Server. We are using a LTO-2 Faststor ADIC tape drive. Network connections are all 100FD on all clients and the backup server. What I see when backing up is 10-11 MB per second. MY clients are all set to Client Parallelism = 7...

First of all Thanks To all. Yes I tried local from the server where GST/Networker is installed. I also checked there is no firewall. This server is on our DMZ. I checked the services file also. I have ports 9000 and 9001 open? Any other Ideas ?

more looking around in the gst logs *** gstd starting at Tue Nov 14 17:26:35 2006borting connection. 11/14/06 17:26:57 gstd: Upgrade/Bootstrapping needed, performing ... 11/14/06 17:27:30 gstd: Done with Upgrade/Bootstrapping 11/14/06 17:30:42 gstd: Aborting connection. 11/14/06 17:30:42 gstd...

After installation of networker 7.3.2 and using for about 6 weeks. I ran into an issue where the management console stopped working after a reboot. I can get to the welcome screen fine , But when I click start to start the management console I get the following message: Unable to connect...

Any one already Running on Networker 7.3.2 and Red Hat Enterprise Linux AS release 4 (Nahant Update 4)Kernel 2.6.9-42.0.2.ELsmp on a DL380 G4 server? Any Issues on the this configuration? I have seen some issues on version 7.2.1 running on AS 3 Red Hat Enterprise Linux AS release 3 (Taroon...