Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by r307

  1. r307

    MICS 4.1 sw

    PRI wasn't supported until MICS 5.0.
  2. r307

    Name and Number CallerID

    Then I agree with Deweyhumbolt - seems that the provider is not sending the calling name.
  3. r307

    Name and Number CallerID

    Question: does each site have it's own PRI or does one site have PRI and CLID is being passed from the main site over the VoIP netowrk? If the latter, is it only the networked sites that are not receiving calling name?
  4. r307

    bcm patch

    Log into "Maintenance", select "Inventory" - from there you'll have a selection to view patches amongst other things about the BCM.
  5. r307

    CS1000S and CCME(cisco call manager express) interoperability(H323)?

    I'm guessing that the H245 Tunneling config was not the answer? I had another thought which causes the same symptom ... IF there happens to be a Cisco PIX Firewall (or two) in this network, disable H323 "fixup protocols" in the PIX. There are two for ports 1718, 1719 and 1720. These fixup...
  6. r307

    BCM Extension Ringback

    Sounds like a config issue to me. Can you provide a little detail as to the configuration? 1. You have 8 Voice Channels (min/max is what? 2/8?) 2. What sort of trunks are incoming to the BCM (PRI, T1 or analog lines?) 3. Is there more than one number that customers dial to get to the call...
  7. r307

    Ip Phone Set Up on BCM50

    There are too many variables to give an answer since you can use DHCP or Static routes. If using VoIP trunks as well, codecs and payloads much match, etc. However, to make things easier than having to read the Network Config and Device config guides, try using the "task based guide"...
  8. r307

    Paging through 2 BCM 400s at the same location

    I don't personally know of a way to do what you are suggesting. Perhaps someone else does. If not: Depending on how many digital, analog and IP sets you require, you may consider an Expansion Gateway configuration. The only thing is in this configuration, the resources available for IP sets...
  9. r307

    SIP on BCM 50 r3

    If this BCM has a MCDN keycode, you can try using BCMMON UIP trace to see if any specific message is being received from the distant end when you attempt a call. If no MCDN keycode, then you can try looking at the feps logs - sometimes the error is obvious (in English). Good luck...
  10. r307

    SIP on BCM 50 r3

    Did you add blocB to line pool access on the set?
  11. r307

    IP 2002 MIC

    If none of the above works - if you make a test call and stamp it (F9*9) and post the feps log, I may be able to help further.
  12. r307

    IP 2002 MIC

    As norstarboy125 mentioned - are you sure ALL of the appropriate ports are open in your routers? Another possibility: Have you got any Cisco Routers or a Cisco PIX firewall in the network? There are some "gotchas" with Cisco/Nortel interop. If Cisco Routers are in the network: Cisco...
  13. r307

    SIP on BCM 50 r3

    It's always best to check the gas before rebuilding the engine, eh? LOL! Sorry I tried to complicate matters.
  14. r307

    SIP on BCM 50 r3

    I forgot to mention, if you feel you have the configuration correct already, you should try a stop/start of the feps service. Sometimes after a number of changes have been made, even if you get a window that states the feps services will be automatically restarted, a manual stop/start as...
  15. r307

    SIP on BCM 50 r3

    Sorry, I'm only familiar with the SIP config when interoping with another BCM or CS1000. However, if I were in your shoes I'd consult the "task based guide" for BCM50 3.0, under IP Telephony. If you've not seen these before, you'll see that they put specific tasked into one fast, easy manual...
See more

Part and Inventory Search

Back
Top