Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by ptsul

  1. ptsul

    I have a cordless set S4 in Hicom300E lost basestation registration

    Hi SBCSU, Thank you for your replies, especially for the CAT info, it was important not to loose so much time. Finally I had in my hands the Cordless Service Manual and the CAT, and as I expected, no need for the CAT to see the Cordless Pins, since everything is record in SLC card, just have...
  2. ptsul

    I have a cordless set S4 in Hicom300E lost basestation registration

    Thank you Donb01 for your reply, At the same room there is a identical phone working, and my colleage tried to register the another phone and we got the same response from the phone ... probably invalid pin. Where can I check the PIN? I leave some more infos about the set...
  3. ptsul

    I have a cordless set S4 in Hicom300E lost basestation registration

    Hi there, I guess it's a noobie question, but the cordless system it's still a bit foggy... I have a Gigaset S4, that was working and suddenly lost registration, it shows something like "no basestation", and it appears on the screen the extension number and the strenght of the radio signal...
  4. ptsul

    HMS400 / Opera PMS problem

    Hi there, Just to leave a note for someone who comes across with something similar. First thing, to the "old M1" guys, the HMS400 it's an external server based on W2003S, with a digital board (Dialogic) to connect to the DLC on M1, Has nothing to do with the Meridian Mail, (and Nortel). It has...
  5. ptsul

    BRI S0 configuration - Block outgoing calls

    Ok guys, Thank you for your answers, it's working, apart from the first "bug" of leaving the out and inc group id by default, which cause the blockage of outgoing calls, the rest was a common error "invalid user", with the tech on site with the TREND it worked, just the patching was on the...
  6. ptsul

    BRI S0 configuration - Block outgoing calls

    Hi, Yes, I set both to 30, but I guess the initial problem was that it was set by default "0", cause now I have just sent the same cfg, and atleast in my softphone i can do calls, I'll see tomorrow morning (here it's 22) if everything is working. One last question, cause I am trying to...
  7. ptsul

    BRI S0 configuration - Block outgoing calls

    Thank you for your answer, Yes, it's when I set to S-BUS and save, and after the reboot, the users can't use the other BRI (T0). The lights I cannot see them, I am doing it remotely and out of working hours, so no one to check that. I am asking in case it's something very basic like the one...
  8. ptsul

    BRI S0 configuration - Block outgoing calls

    Hi there, Can somebody give me a hit, I am setting up a BRI S0 from a DaugtherB 2BRI in IPO500V2 R8.1, to connect a PC ISDN board, and when it reboots it's not possible to do external calls, which is on the other DB card 2BRI. It's connected with a cross cable and with the 100ohms at both...
  9. ptsul

    Entopia mail replacement

    Hi, Just check if the disk starts (you can feel the vibration and the noise) and check the AML on LD48 and the AX tty , disable and enable both. Make sure the TTY port(hardware) for AML is ok, or it won't send the ID (FOX) and it gets stuck there...as far as I remember long long time ago. I...
  10. ptsul

    Is it possible to configure a BRI ISDN ETSI NT

    Once again Thank you all. I will setup and test the connection between the IPO in NT mode and Avaya(Nortel) TE mode, and later with a Siemens TE mode, then I will post the results. Best regards JMF
  11. ptsul

    Is it possible to configure a BRI ISDN ETSI NT

    Thank you amriddle, Sorry but I am a new in IPO500 world, in fact I have our lab system now to startup. Some more doubts: - does any BRI card supports the S-Bus configuration,as you mention, including the comboBRI card? - Do I need to have a special NT (ISDN Network Terminator)or a common one...
  12. ptsul

    Is it possible to configure a BRI ISDN ETSI NT

    Hi All, In IP Office 500 V2 R6 is it possible to configure the BRI unit in NT mode (ETSI) to interconnect to other system in TE mode? Thank you all!
  13. ptsul

    No name displayed on the night service phone

    Hi all Thanks for the quick reply, GHTROUT , your sugestion did the job, I did the test and it works ??!?!? but I am confused ... by the NTP (DNDD) Dialed Name Display Denied DNDA Dialed Name Display Allowed after all this time, always find some funny ones like this one, and thinking that...
  14. ptsul

    No name displayed on the night service phone

    Hi all, Is this a BUG or is like this and it always has been like this. - already check on 3 different sites and releases and they all do the same. (rls 22.46, 25.40b, 04.50w) When I dial the night service DN, it shows the originate DN and name as usual. When the ATT is set to night service...
  15. ptsul

    How to get a delay on TSC code and DN

    Hi all, Here is something that i really need some help(and I have lots of ***** to give), after reading all the NPTs and testing for 2 weeks, I still cannot make this work, and the worse is that with other "small" systems it's possible to do it. I need to implement the following scenario: - a...
See more

Part and Inventory Search

Back
Top