Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Recent content by primeaum
-
QoS Help
From what I understand, our service provider doesn't look at our traffic on the P2P. I guess I would be either marking the traffic or just relying on NBAR to detect properly. I would like to make traffic going over the p2p have high priority or a set amount of bandwidth to and from a certain IP... -
QoS Help
Hello, I'm looking for some basic QoS setup for AS400 traffic. I need this traffic to have the highest priority. I currently have a P2P T1 and a VPN Tunnel that have the same costs between a facility and the corporate office. Traffic flows over both of these links with no issues. I would like... -
Recommended network switches - Harsh environment
Thanks for the suggestion. We have a closet that has like 8 24-port switches in it and I was actually looking for 48ports to replace them with. I guess HP used to make a 48 port that was fanless, but it is no longer produced. I suppose we'll just continue using the cheaper HP/3com switches in...- primeaum
- Post #3
- Forum: Data Transmission general discussion
-
Recommended network switches - Harsh environment
Hello, I'm looking for any recommendations on network switches to be used in a harsh environment. I'm talking warehouse/manufacturing. What can a Cisco 2960-s do better than an HP V1910? would there be any reason to go with a Cisco over an HP? Even with basic configurations on both (maybe...- primeaum
- Thread
- Replies: 2
- Forum: Data Transmission general discussion
-
Cisco AP with PoE Injector not working with Netgear switch
Thanks, I'll give that a shot.- primeaum
- Post #3
- Forum: Wireless Data and Devices
-
Cisco AP with PoE Injector not working with Netgear switch
I have a NetGear ProSafe GSM7248 that I have been forced to use. I was told to get a Cisco AP on this network as well. I have a cheap Cisco switch for testing. So my Cisco 1260 AP works with the injector when plugged into the Cisco switch, and a small DLink switch, but not when plugged into the...- primeaum
- Thread
- Replies: 2
- Forum: Wireless Data and Devices
-
New Site - Recommended hardware? VLAN's required
Good afternoon, I am being tasked with setting up a new site for my company. We will need at a minimum 2 VLAN's. We currently have an ASA5505 and a Cisco 2811 router that can be used. We will start with an internet T1 and add MPLS down the road. The internet T1 will have a site-to-site VPN to... -
Outlook 2007 not sending attachments while on Cisco VPN
Help! I'm having an issue where a remote user cannot send emails while connected using the Cisco VPN Client. This usually starts with emails containing attachments but then stops altogether. Any ideas? I've changed the MTU several times and still get the same results...(on the Cisco Systems VPN...- primeaum
- Thread
- Replies: 0
- Forum: Microsoft: Exchange
-
MPLS
My company is looking at going to MPLS from point to points. I'm looking for some info on MPLS and people who may have gone through such a transition. We have our own routers right now and the company that did the originally setup created VLANS on the routers themselves instead of core...- primeaum
- Thread
- Replies: 1
- Forum: Data Transmission general discussion
-
Redundant router help
So it seems that web pages have been loading fine but large downloads stop in the middle. I am also seeing a VPN (not the IPSEC/GRE Tunnels) drop from time to time. what gives? -
Redundant router help
Via the GRE tunnels. They are created on both the firewalls and the routers, so on the routers they look like point to points and internal traffic is routed using OSPF. -
Redundant router help
If you do a "show glbp", are state changes being recorded? What are the counters showing? To be honest I don't think GLBP is the problem, unless the dropping started just as you started using it. FastEthernet0/0.1 - Group 10 State is Active 2 state changes, last state change 1d00h... -
Redundant router help
I have GLBP setup on both routers and some users have complained that web pages don't come up sometimes. If they hit refresh a few times it loads fine. I'm also using RDP to connect to a remote PC and lose connectivity every couple of minutes. Any ideas? Here is the setup: Router 1 interface... -
Redundant router help
they are primary connections. I've never setup DMVPN but I will read up on it. Thanks for your time. -
Redundant router help
I have pretty much two of everything and need to make it as redundant as possible. I need to have a site-to-site VPN tunnel to our corporate offices too. This is created on the ASA's and then a tunnel on the 2811's. Right now I have a tunnel to our Corporate office on one of the ASA's working...
