Recent content by prabath

That means when delivering mails it looks for whole part of the domain name (@y.x.a.com) ,not only the a.com . am I correct ? for example take xxxx@y.x.a.com e mail address. Will the sending mail server look only for the a.com and send it to the destination ? and recieving server take action...

I want to implement exchange based email system that represent @ a.com @ x.a.com @ y.a.com @k.y.a.com Is it possible to register a single domain name (a.com)and implement this system. And also need to know whether this is possible with single exchange server.

I am getting error message when OWA client(Internet explorer) try to connect to the OWA server. (windows 2000 with exchange 2000)--------(NT 4 with MS Proxy 2)----(Internet)------(Symantec firewall with network address translation)-----(workstations with internet explorer) In this situation it...

Resolved by removing call rsvp-sync in 3662 router.... Can't believe.... Can anyone explane this ? (I think this command is used to combine voice with rsvp on the interface....But there were no rsvp on ethernet that we used for testing.... Another problem is why this delay occured only when...

It is E1 (NM-HDV-2E1) 3662 config dial-peer voice 6030 voip destination-pattern 03. session target ipv4:192.168.10.235 tech-prefix 6 dial-peer voice 2 pots destination-pattern .... direct-inward-dial port 4/0:1 forward-digits all call rsvp-sync voice-port 4/0:1 voice-port 4/1:1 mgcp...

I have a problem with my voip setup so I created a lab setup to test this. Tele phone 1-----PBX----3662----ethernet----1750/1751-----tele phone 2 telephone 2(1750)-----telephone 1 (3 seconds between dialing digits & hearing ring back tone from telephone 2) telephone...

We have the voip network which connnect branch offices to the head office and both routers are connected to the PBXs. Can any one tell me whether is it possible to make call from their branch offices to the PSTN that located behind the head office PBX?

Hello Kev, The idea you gave is verry useful; Thank you so much! I choosed 3 images, ENTERPRISE PLUS/H323 MCM c3660-jsx-mz.122-13.T.bin ENTERPRISE PLUS IPSEC 56 c3660-jk8s-mz.122-13.T.bin ENTERPRISE/SNASW PLUS IPSEC 56 c3660-a3jk8s-mz.122- 13.T.bin But I...

I need to select IOS for a 3662 router with the following fetures. ENTERPRISE PLUS/H323 MCM (multimedia conference manager) ENTERPRISE/SNASW PLUS ENTERPRISE PLUS IPSEC 56 I tried cisco IOS feature navigator but when I filter with 2 features above, 3662 was disappeard in supported flatform...

Thanks, It is amazing your way of catogarizing things for beter understanding! Prabath

PBX----e1----3662--e1---ds0'S---1750 with FXS---PBX This is the setup we are having.Failure occurs in E1 between PBX and 3662 as explained above (only some channels hangs). In the same setup 1750's voice functions also hangs(users can't hear dial tone)But I don't know this two problems are...

We have voice setup which connects 3662 to PBX with E1 line usin multiflex trunk line (NM HDV 2E1 60). sh voice port Port ch sig-type oper in status out status tip ring 4/0:1 8 R2-analog up idle idle 4/0:1 10 R2-analog up idle idle 4/0:1 17 R2-analog up idle idle 4/0:1 26 R2-analog up idle...

Thanks lot, You made my whole day easier cool and happy!

Can anybody tell me the GBIC module use to connect 2950G 48 EI and 3550 12 G? Both should equiped with theas GBICS which used to link by multimode fiber. Thanks,

We have voip setup with lucent PBX, 3662 Router and 1750 2v routers. Last week we added new 1751-v router but it is giving call initiating problem. Extentions that are behind the PBX can't initiate calls:they can't hear ring-back tone(keep silent) and far end extention gives only one ring and...