Recent content by pops185

Actually its -24 volts that are required for the self-amp speakers Pops185:)

I have done something like this before but not with an IP phone ....I have installed 5 / 10 watt SELF AMP speakers off the speaker leads on the phone 64xx and 44xx series so that when someone calls the phone and it rings it also rings through the speaker (and stops when the receiver is picked...

Ip Guru What happened to the link to your ftp site ?? as it had some great info and some old admin files I can no longer find ...I have to upgrade a IP403 from 1.3 to 2.1(27) I think you have to go to 1.4 before 1.99 and in order 1.3 to 1.4 1.4 to 1.99 1.99 to 2.0.xx 2.0.xx to 2.1.27 All...

Thanks solvic, I think we're on the right track, But when I do a sta trunk group, I get disconnected NE. I just crosswired the 1 pair circuit to the 1st pair of the 25 pair cable. I put in 2 users in the ch bri page is that right? Thanks in advance.

Customer has T1 with a BRI for a backup. I have never setup a BRI before. I went to add bri a09, what do I put in the fields, network? user? Slave? What protocol? Help

We have just installed a IP406 with 16 port & 30 port digital Modules ....running 3.0.40 on IP406 Modules are 5.0.40 Expansion unit 1 is a 16 port digital unit Expansion unit 2 is a 30 port digital unit Expansion unit 3 is a 16 port Trunk unit Expansion unit 4 is a 16 port Trunk unit *Not...

I think you want to use W2KTT .......make sure its caps to pops185

I tried ** config and config as password it would not let me in ....any backdoors through programming as the default should be config I thought ???? pops185:)

I have worked on Northstar 8x24 and added lines ... programmed to ring , ring & appr , appr but how do you add / delete lines in the "small" compact Northstar plus logging in with **config ....admin I can go into terminal & sets .....go into stations and see lines assigned to buttons b01 -...

Nugifirst Yes I did have a fixed address (192.168.42.2 with 255.255.255.0 as netmask) I always set my machine to 192.168.42.2......leaving the manger tftp log open just shows the date ..... I see nothing in tftp log other then after reboot: Fri 29/4/2005 08:36:56 : Log starts I will try...

unit failed upgrading ....getting red light on unit open tftp log in Manager as 255.255.255.255 unit was 192.168.42.1 ( manager pc 192.168.42.2) I see nothing in tftp log other then after reboot: Fri 29/4/2005 08:36:56 : Log starts Manager still has the boot directory from before: MAC...

Matt Yes I guess your are entering the address by hand and not dhcp ..... its should ask you for : EXT # and then Password after you have set the ip address on the phone ....I always leave it at 1234 as its easy to remeber if a user has an issue but you can use what you like cheers:) pops185

Matt Its located in the user tab just below name its says Name John password 1234 confirm password 1234 Full Name John Smith cheers: Pops185

When I did the upgrade to 3.0 I went to 2.99 first then to 3.0(40) ......BLF buttons do not light up on 4412 or 6408D+ sets ....yet if I assign one to 4610SW phones it does work (turns gray)...also park buttons do not light up but do function as they place calls in park button action...

sounds like you use BA instead ?? Bridged Appearance (BA) - this is a copy of one of another users Call Appearances, it can be used to make or receive calls on behalf of the owner of the Call Appearance but you lose the "tranfer" function of Busy Indicators ?? pops185