Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by phneguy

  1. phneguy

    VM PRO stopping???

    the licenses are valid. that was the first thing we checked. i will see what the "recovery" is set to as well. i will download the new release and see what happens. thanks for the replys guys.
  2. phneguy

    VM PRO stopping???

    Hey guys, ive run into a trouble that i cant seem to pin down??? i have a customer with a 406v2 and Voicemail Pro. both are 4.1 the problem is that the VM PRO keeps stopping?? i dont know what is making this happen? any suggestions would be great!
  3. phneguy

    Upgraded to 4.1 on IP 406 now reboots randomly

    what type of sets are you using? i had an issue with a 406v2, 30 port digital module, and 5410 sets. i tried to put a 4424D+ set on the system to get more buttons with lights, and the system started rebooting immediately after i hooked it up. we took it off, and the reboot stopped.
  4. phneguy

    auto intercom on 4.1

    hey guys, i changed the programming to "Direct Dial" and it works fine until the Receptionist gets more than one call at the same time. when this happens, she has to place ALL incoming calls on hold/park to be able the page/direct dial the extension to notify the person of a call then...
  5. phneguy

    neatgear FVS338 to netgear FVS114

    hey guys, got it to work! thanks for the help!! i think it was that i was putting the wrong local gateway ip address. i put the gateway address of the ip office location in the ip route and it started working. thanks and sorry for the brain fart!!!
  6. phneguy

    neatgear FVS338 to netgear FVS114

    i can ping hosts across the network, but i cant ping the IP OFFICE. in both the 338 and the 114 the VPN shows connected. i can ping other computers on the far end. i have the IP route in the ip office as follows... ip address 66.0.7.0 subnet 255.255.255.0 gateway should i put the ip...
  7. phneguy

    neatgear FVS338 to netgear FVS114

    Hey Guys, just wondering if anyone has set up a VPN with the following routers... FVS338 (at main location) to FVS114 (at remote location)?? i have the VPN tunnel built and the phone gettings it files. after it gets its files, i get a blank screen then...Discover xxx.xxx.xxx.xxx i do have...
  8. phneguy

    Avaya SG License

    Hey Guys, just wondering if anyone has anyway to get some Avaya SG user licenses? we have a couple of these that we would like to use. thanks!
  9. phneguy

    VPN Remotephone question

    sorry about that... i do have that tech tip. it works very good, but i think the Generic PSK set up is wrong (i cant save the password in the flash memory). do you think if i change the set up on the Netgear router and the VPN phone to "mode config" this should fix the problem? do you think...
  10. phneguy

    VPN Remotephone question

    how do i find that??
  11. phneguy

    VPN Remotephone question

    Hey guys, just wondering how to set a VPN remote phone to plug into ANY network to connect to the IP OFFICE without having to reprogram the phone? i know you can do this with the Avaya SG routers, but is there something else you can use? is there any other router that will let you do the same...
  12. phneguy

    netgear fvs338 question

    Hey guys, i have the Netgear FVS338 with a Remotephone that works fine, but when it reboots, it does not save the programming in the phone. in other words, i have to reprogram the phone EVERY time it powers off. i have the phone set up as a "generic PSK" device. this mode does not give me...
  13. phneguy

    auto intercom on 4.1

    has the way you "voice call" someone changed in the 4.1 software? we have a customer who uses this feature a lot and hates the way you have to do the "auto intercom" with 4.1. is there any other way to do this. right now the customer has to press the # button to start the page? do i need to...
  14. phneguy

    SIP Trunks

    Do i need to set up an IP ROUTE in the IP Office for SIP trunking?
  15. phneguy

    is there a way to "monitor" calls

    sorry for the brain fart!!!! i didnt even think of using "call status" thanks Westi!!
See more

Part and Inventory Search

Back
Top