Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by phdude

  1. phdude

    M 7208 won't hang up on CICS

    When I tried to look for restrictions I think it led me to night schedule. I could not find the default filters list. As always thanks for the help.[bigsmile]
  2. phdude

    Memory Battery on a Partner 206 v 2.0

    Have you used the partner plus / partner II battery in the partner? thanks
  3. phdude

    Memory Battery on a Partner 206 v 2.0

    Mine is a Partner 206 v 2.0 however mine has three legs not two. I left a message for refurb supplies, but never heard back from them. I appreciate your help though.
  4. phdude

    Memory Battery on a Partner 206 v 2.0

    Any suggestion on a supplier? Varta site had a wrong battery listed on web site.
  5. phdude

    M 7208 won't hang up on CICS

    I'll check it for sure. I do know it does it on outside calls. I'll check intercom calls tonight.
  6. phdude

    Memory Battery on a Partner 206 v 2.0

    Can someone give me the VARTA or other manf. part number for a memory battery. Mine is a double stacked coin type battery with three legs to board. Some folks gave me a varta number but it had only two legs to board. System is Partner 206 v 2.0. Thanks as always for this forum and it's members!
  7. phdude

    M 7208 won't hang up on CICS

    I have a location with a M7208 that won't hang up. I have placed three phones at same ext and none will hang up everytime. System is CICS ver 4.0 or better. Also need help to program restrictions for no long distance at several exts. I can't seem to find the restiction program as I normally do...
  8. phdude

    Mitel SX 200 Help with restriction that won't release

    Do you use N 8 1 ?
  9. phdude

    walking around away from her station 221

    I have a client with a 0x32 v 4.0 and here is what they want: When 221 is up walking around away from her station they would like all incoming calls to start ringing after 3 unanswered rings at some other phones (copy room(239), break room(241), etc. Can someone direct me to the program to do...
  10. phdude

    Mitel SX 200 Help with restriction that won't release

    Hey Avaya Guy thanks so much for the help. What protocol do I use to get hooked up? What is the PMS system?(I know if you have to ask you don't/ should not be told). If your NOT using a PMS system, verify: FUNCTION GUEST ROOM DIAL EXT.# STATUS -change to LOCAL, LONG DIST, or INTERNAL How do...
  11. phdude

    Mitel SX 200 Help with restriction that won't release

    The only programming tool I have is the console. I will try your suggestions. Manager says ext 117 has been getting a fast busy for two years.........ever since someone programmed the switch to be able to put restrictions on. (imagine that) I was able to clear restriction on ext 299 by hitting...
  12. phdude

    Mitel SX 200 Help with restriction that won't release

    Calling restrictions such as local dialing only or no long distance. Currently it will only call room to room or room to operator. thanks
  13. phdude

    ACS Fax programming

    They do have a remote access card and voice mail but niether are installed just yet. So I guess you are saying that these need to be installed before programming ext 16 for fax. Do I need to do anything special with ringing? thanks
  14. phdude

    ACS Fax programming

    I want them to share with phone system on line 2. Does it have fax detection that will send a fax call straight to fax machine and ring a voice call phone call thru to other exts? Thanks
  15. phdude

    ACS Fax programming

    I have a client with an ACS and I would like to know the procedure for programming a fax machine port. I set #601 or # 602 (can't remember) but it answered all incoming calls(both lines). What should I do to complete a working fax port. I know there must be a simple step I'm overlooking. As...
See more

Part and Inventory Search

Back
Top