Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by pganoe

  1. pganoe

    G430 enable interfaces

    you need to use the "set port" commands to enable and configure the physical ports. PG
  2. pganoe

    MM not giving personal greetings to new LSP exts

    Check that you have the new range in public or private unknown. PG
  3. pganoe

    Only 8 rings on Call Forward and then voicemail

    Do "change system-parameters coverage-forwarding". On page 2 check that "Coverage of Calls Redirected Off-Net Enabled?" is set to y. PG
  4. pganoe

    How to configure my PRIs so the carrier can loop them?

    You need to have the little fire cracker thingy installed between the CSU and the network: 700406101 1 DS1 LOOPBACK JACK 700A RHS PG
  5. pganoe

    S87XX servers

    XL versus Standard Differences: Trunks from 8,000 to 12,000 CLAN Boards from 64 to 106 EC500 Enhanced CLID Support from 54,000 to 108,000 off-PBX station-mappings Tone Detectors: from 1,200 to 8,000 Announcements: from 3,000 to 9,000 VAL boards: from 10 to 128 Attendants & attendant groups...
  6. pganoe

    Changing the name on the system greeting from old user to new user

    From the main menu try pressing 5 for personal options and then 5 for record name. PG
  7. pganoe

    about dhcp

    If it's coming up on VLAN 0, I would suspect that the TESTVLAN timer ran out before it got an address and so it is using that value. Do a CLEAR# on the phone and try it again. PG
  8. pganoe

    about dhcp

    Doubt 1: You only need teh VLAN info in the desktop scope. L2Q=1,L2VLAN=200 Doubt 2: You can have the L2VLAN=200 in the desktop scope because the desk tops won't be looking at option 176 or 224 and probably don't have the ability to tag anyway. Doubt 3: 1= L2Q on, 0=L2q auto The config you...
  9. pganoe

    about dhcp

    You need to add the DHCP options, 176 and 242 to your desktop scope as well. You only need the L2Q=0 and L2QVLAN=200 strings, that way the phones will know they are on the wrong VLAN and reboot on VLAN 200. I always use L2Q=1, but I don't know that what you have won't work. PG
  10. pganoe

    Definity CSU 120 A3 cable to PRI Jack from LEC

    I don't know the pinout of the cable or what's connected other then 1,2,4 and 5, but 700395445 is the comcode for the 50 ft cable The firecracker is a loopback device. The CSU 120 and the MM710 have no internal loopback capacity. PG
  11. pganoe

    Definity CSU 120 A3 cable to PRI Jack from LEC

    700395445 1 120A CSU CABLE 50FT RHS A1 $30.00 PG
  12. pganoe

    embeded CMM

    Have you checked that the Node number in Dial Paramenters and in Switch Link are the same? PG
  13. pganoe

    Turn Off Tenant Partitioning

    Problem: Unable to load new license with Tenant Partitioning turned off. Platform: S8300/G450 CM5.2 Background: Single site S8300 with G450. We want to use Attendant Backup, which requires that tenant partitioning not be enabled. The current license has TN enabled, I have created a new license...
  14. pganoe

    CSS M?

    Controlled Slip Seconds. The number of seconds (maximum of 255)with one or more controlled slips (a replication or deletion of a DS1 frame by the receiver).
  15. pganoe

    Flash Backup

    I have a customer with S8500 CM5. We are doing weekly backups to flash and I have selected save 9 data sets of data. The problem is it is only saving the last 4. This is a fairly small system so I can't imagine that the card is full. Anybody know what I have done wrong? Thanks PG
See more

Part and Inventory Search

Back
Top