Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by paulux

  1. paulux

    Getting back on track...

    Hey CiscoGuy33, I'm doing router on stick with my 2610. IOS version12.2(46a). Cheers, Paul
  2. paulux

    IBM Netfinity4500r problems...

    Vittorio, Thanks for your response. server 1: model 5RY ram - slot 1: 128mb ram, pc133 with ibm sticker on it. slot 2: 1GB pc133, aftermarket. Bios version 11 server 2: model 4RY ram - slot 1: 128mb ram, with ibm sticker on it. slot 2: 512mb, aftermarket, pc133 slot 3: 512mb, aftermarket...
  3. paulux

    IBM Netfinity4500r problems...

    I was given two netfinity 4500r servers from a co-worker, both of which say, "processor 1 not functioning" on bootup. The person I got them from knows nothing about the history other than one was used as a mail server at some point and one was running some linux. What are the odds that both...
  4. paulux

    Console Password

    Here is the link to the password recovery instructions: http://www.cisco.com/en/US/products/hw/routers/ps233/products_password_recovery09186a0080094795.shtml
  5. paulux

    copy ios from tftp server to 2950 with no file in flash

    Nevermind...of course I would find the answer after posting the question here. In case anyone was wondering, the baud rate is stored in flash:env_vars. The more I learn, the less I seem to know.
  6. paulux

    copy ios from tftp server to 2950 with no file in flash

    A new problem relating to this issue: I copied the file over via xmodem at speed of 115200, now when I connect via the console cable, it will only accept a speed of 11520. I do this, then go in and change the line con 0 speed to 9600 baud, it changes, but the speed keeps defaulting back to...
  7. paulux

    catos boots into rommon

    Still no luck: rommon 2 > boot bootflash:cat4000.5-5-21.bin CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC0:00.576610: Please set IPAddr variable 0:00.577197: Please set Netmask variable 0:00.577556: Please set Broadcast...
  8. paulux

    catos boots into rommon

    thanks for the prompt response vipergg - I appreciate it. I tried the recommended commands, but still boot into rommon. Am I doing something wrong? rommon 3 > set boot config-register 0xf rommon 4 > clear boot system all Usage: clear boot rommon 5 > set boot system flash...
  9. paulux

    catos boots into rommon

    I've read through the posts about resolving boot problems, as well as numerous cisco docs, but my 2948 keeps booting to rommon. What am I doing wrong here? As usual, any help will be GREATLY appreciated! Thanks in advance vipergg ;-) rommon 3 > dir bootflash: File size...
  10. paulux

    copy ios from tftp server to 2950 with no file in flash

    Thanks vipergg...that solved it! What a convoluted process that was. Oh well, you learn something new every day. A star for you!
  11. paulux

    copy ios from tftp server to 2950 with no file in flash

    SO...I screwed up and deleted the flash on my 2950. I uploaded the bin file from another 2950 to my tftp server, but how do I copy this file from the tftp to the 2950 with the deleted flash? I can't believe how much time I have wasted trying to figure this out! The following is the prompt I'm...
  12. paulux

    Asked 100 times but...I want to start a Router Lab

    If you decide to get the equipment, instead of using dynamips, which would also be a good option, get the pieces individually. You will save a LOT of money that way.
  13. paulux

    CCNP Home Lab Setup

    After doing my research, so far I have gotten 2 2950s on ebay for right around $100 each. I got 3 2610s in a set on ebay for $90, two of which came w/56k DSU/CSU cards. I'm glad to get some hands on with the hardware – it has opened my eyes to how much more intricate this all is than you can...
  14. paulux

    CCNA

    burtsbees , I am back and forth about whether or not to begin the CCNP. I just got my CCNA, using simulators to apply the concepts. I am purchasing the equipment now to setup a home lab, but do not have work experience using Cisco equipment. So my question, you said you have no experience, but...
  15. paulux

    CCNP Home Lab Setup

    Burt, Thanks for the feedback. I"m going to start shopping around for the equipment soon! Paul
See more

Part and Inventory Search

Back
Top