Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by PareshTC

  1. PareshTC

    Name Transmission over DPNSS Link

    I have a Nortel CS1000E Rls 5.5 pbx talking to a Mitel 3300 switch over a DPNSS link within the same premises. The problem I am facing is that the CPND display name is not working correctly, - I can see name showing on incoming calls from the MITEL system but the Nortel PBX cannot use it to...
  2. PareshTC

    Name Display Over QSIG Protocol

    Does the DCH have RCAP ND2 enabled?
  3. PareshTC

    NTBK51AA switch seetings to DNUM 16?

    The DNUM is only group specific, i.e. you can have 0-15 in grp0 and another 0-15 in grp1. Thus on your 2-group 81C system you can have 32 DNUM's in all
  4. PareshTC

    Nortel to Cisco T1s

    Always try and use only 1 Loop within a route and keep route and loop numbers identical for tracking. This way I can control via RLB's what routes are used for incoming and what for outgoing. Dunno if that would work for all setups though, but i found it helps simplify call routing.
  5. PareshTC

    i2007 Phones with full DHCP cannot boot after isetResetAll

    The DHCP string for all wired Nortel IP phones can only be the i2004 string. There are only 2 variations of it, Nortel-i2004-A and Nortel-i2004-B depending on phone firmware and features required. Also if the DHCP string is wrong, how do the phones accept it when physically rebooted? As...
  6. PareshTC

    i2007 Phones with full DHCP cannot boot after isetResetAll

    Hi, Got a wierd problem. IP phones 2007 and 1140 setup with full DHCP and Auto Prov on Unistim 4.0 When I do an isetResetAll from the sigserver, the 1140 phones reboot correctly. However the 2007 sets fail at the DHCP stage. They cannot understand the DHCP string sent by the DHCP server. Only...
  7. PareshTC

    CPPM Redunduncy

    Firstly, if you initiated a manual reboot of the system, using the RST switch on faceplate, the stadnby CPU wil lrecognise this as a planned reboot and reboot itself. However if you were to simply pull the active card or ELAN cable from active (neither is suggested), it would have simulated...
  8. PareshTC

    Mobex Not working

    Thanks for the quick response Mr SL1M1 :-) But I am not using the mobile route solution. Instead I am using the MSA-DN solution, wherein a normal trunk route is being used for the calls. Also I have traced the DASS2 circuit and can see the CLI on the messages as well as normal desk phone...
  9. PareshTC

    Mobex Not working

    Thanks for your reply, could you explain what you mean by "check out the IDC table so that the Mobx number points to the mobile number"?? As per my understanding, the DDI number that will be used by the mobex needs to be mapped to an MSA-DN within the CS1000. Once the call hits the MSA-DN, the...
  10. PareshTC

    Mobex Not working

    Hi All, Got a problem with getting Mobex to work on a CS1000E 5.5 system. I am using the MSA feature rather than the dedicated route config. I am able to correctly call the mobile phone when the desk phone is called, however this is just PCA rather than the Mobex functionality. I have...
  11. PareshTC

    Conitnous ringback tone

    Hi All, I have got a very interesting problem, which I have not been able to crack so far. Hope someone here can help with it. Scenario : DDI call over Euro ISDN trunks need to be given an annoucement telling them that the call may be recorded My setup : Map the DDI in IDC table to a ACDN...
  12. PareshTC

    MWI on BT-ITS Dealerboard

    Hi All, After working with the BR-ITS developers, we found out that you need to have RCAP no set to MWI for the message waiting to work. Wierd, but it works just fine. Solution ==> For integration with BT-ITS dealerboard over SL1 *do not* have RCAP=MWI.
  13. PareshTC

    MWI on BT-ITS Dealerboard

    Hi All, Thanks for all the replies. My problem is that the NMS Message goes out with a STATUS of UNKNOWN instead of MWI-ON or OFF. This i think might be related to a discovery I made yesterday. Callpilot seem to have NMS==>no in the licenses. This is interesting as the Features and Services in...
  14. PareshTC

    MWI on BT-ITS Dealerboard

    @GHTROUT I see that you have been comparing the two systems on other threads, do you have any information. Did you manage to get the MWI working
  15. PareshTC

    MWI on BT-ITS Dealerboard

    RCAP = ND2 TAT MWI
See more

Part and Inventory Search

Back
Top