Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by pakojones

  1. pakojones

    Adding a voicemail or announcement to a ring group

    Hi UncleRalph Finally I think I understand what you mean, I setted up a mailbox with the number of the ring group with an alternate extension, when no answer on the ring group it goes to the VM and the MWI of the alternate extension lights on :-) Thanks!
  2. pakojones

    Adding a voicemail or announcement to a ring group

    UncleRalph, I don't understand what you mean, could you explain it a bit more?. Thanks.
  3. pakojones

    Adding a voicemail or announcement to a ring group

    Hi, I have the same problem, do you know if this also works using Nupoint?, I tried to setup this with MCD 4.0: Ring group: 4400 with overflow to *4500 Hunt group (Nametag type): *4500 with no members and always routed to 3500 (Nupoint Hunt group) But when I call to 4400 it goes to MBX 4400...
  4. pakojones

    MXe II Maximum mailboxes

    Thanks!
  5. pakojones

    MXe II Maximum mailboxes

    Hi, I have a MXe with MCD 4.0 and a E2T card installed, the controller has about 500 SIP extensions. With this config, how many mailboxes is able to handle the controller? Thanks.
  6. pakojones

    Modify incoming caller id

    OOPS :( Thanks for the answer :-)
  7. pakojones

    Modify incoming caller id

    Hi, I have a ICP3300 with MCD 4.0, recently I configured a PRI to send calls to corporate cells, internal extensions (Mitel 5312) are 4xxx and cell extension are 6xxx. When a cell extension makes a call to a internal extension the telco sends a prefix on the origin and destination numbers, so...
  8. pakojones

    Call forwarding and voicemail

    kwbMitel, the user on 4811 needs sometimes to forward all calls to 4811 which is a valid destination (another 5312) When the forward always is active, internal calls rings on 4811 as it is supposed to work, but when the call is from PSTN, it immediately goes to voicemail. The help says that...
  9. pakojones

    Call forwarding and voicemail

    Hi again, I'll try to explain better. The extension with the problem is 4871, the controller has two PRI with 150 DDI, to get the correct extension the controller absorb the first 6 numbers and insert '4'. If I call to the extension from i.e. 4801 it works fine, but if I call from PSTN to...
  10. pakojones

    Call forwarding and voicemail

    Hi, kwbMitel, no, I set the forward as always on the phone, if this helps, the phone is a Mitel 5312. IP Device ID: 633 Circuit Location : 1 3 6 8 1 Extension :4871 Active Features : Call Forward Always : 4811...
  11. pakojones

    Call forwarding and voicemail

    Hi BrantN, Yes, the call rerouting assignment is set to go to voicemail, and I am setting the forward on set side. Thanks. Jesus.
  12. pakojones

    Call forwarding and voicemail

    Hi, I have a 3300 MXe with software 10.0.1.22 with some extensions configured with voicemail, on Call Rerouting Asignment I have a first alternative to the voicemail extension, this is working fine. Now I need to enable call forwarding on one phone for all calls, but when I configure it on the...
  13. pakojones

    3300ICP random reboots

    Thanks to all for your answers, but finally I will install everything on another ICP controllers from scratch, because this system has been upgraded by another guy, and maybe he made a mistake :-( Thanks again :-)
  14. pakojones

    3300ICP random reboots

    One question, If I execute UpgradeBootrom E2T and the card need to be upgraded, when it finishes upgrading, it reboots automaticly, or it offer the option to reboot later? Thanks.
  15. pakojones

    3300ICP random reboots

    I have a doubt, is this IP config correct? For icpsys1 System IP Address: 10.1.0.10 Subnet Mask: 255.255.0.0 Gateway IP Address: 10.1.0.11 Layer 2 (L2) Switch IP Address: 10.1.0.11 E2T Card IP Address: 10.1.0.12 / 255.255.0.0...
See more

Part and Inventory Search

Back
Top