Recent content by PainOfDeath

There are no whitelists/blacklists or anything of that sort on the network. I tried creating allow rules on the hypervisor firewall, and just disabling the firewall altogether, but it made no difference. The switch equipment is Netgear with an Untangle router but I have tried other...

Wondering if anyone has experienced this or similar; seems to be my network/hypervisor so E-MetroTel can't assist further. I have had a UCX version 7 running in my home office environment for a few months, with an assortment of XSTIM/Unistim phones, both on site and remote, digital and IP...

In case anyone is wondering, e-Metrotel has issued a patch for the Digital Gateway that resolves the static issue. My T7406e phones now all work flawlessly. Adjusting the FXO gain also resolved the fax problem. Now if they would only update their logo...

Hey ucxguy, One of the first things I did was change the phone type to T7406 for the cordless extensions, but when I checked the extensions overview, they are listed as M7310! The extensions are individually set to T7406 - I will see if e-Metrotel support can help. As for the fax, the AGC and...

Hello, I recently migrated a Norstar CICS to a UCX50. Almost everything works normally but there are a few nagging issues that I can't seem to figure out. 1. T7406e cordless sets, which worked perfectly fine on the CICS, now have bad static which renders them unusable. 6 sets in total on two...

The default password doesn't work. I don't mind losing all the configuration info, but I'd really like to keep the licenses intact. I have read that level 1 reset does not wipe out keycodes, and elsewhere I have read that it does, so I am not sure. Does anyone here know for certain?

Hello, I am trying to log in to a BCM50 2.0 for which I don't know the nnadmin password. If I do a level 1 reset, will it set this to the default? Will the level 1 reset wipe out the keycodes as well? If it does, is there a way to reset the password using a telset and avoid wiping out...

Update: I resolved the problem by removing the add-on card that was included with the router (I did not require it anyway). The system now boots normally!

Thanks. I booted back into the recovery mode and was able to load version 4.85 onto the unit. However when I restarted it, I was greeted with the following: Performing Check Disk on [/ide1/] ... Copyright (c) 1993-1996 RST Software Industries Ltd. Israel. All rights reserved ver: 2.6 FCS Disk...

Hello everyone, I purchased a used Contivity 1100 (eBay) that does not successfully boot. It would get to the point just after the disk check and halt there. I booted the unit into recovery mode and was able to access the web-based tools but there did not seem to be a way to recover the...

Hello, I am looking at a scenario where I would be upgrading an Exchange 2003 server to Exchange 2007. Currently I have RPC over HTTP implemented. Will Exchange 2007 on Windows 2008 standard also support RPC over HTTP? I was looking a feature comparison between 2008 standard and enterprise, and...

It turns out that the e-mail address being used in one case was wrong, so there was no problem internally. As I said, MX records and DNS is fine. I looked into creating an SPF record but I use DynDNS and am not sure how to add that record. Can anyone tell me how?

This problem only started when we switched from iMail to Exchange 2003. There are a few domains that won't accept mail from ours the user gets the following message in an NDR: You do not have permission to send to this recipient. For assistance, contact your system administrator...

I think you are going to have to use COS then, but ptstechnician's idea is simpler since with COS you have to enter 9 followed by F68 followed by the 6-digit password which is 10 button presses total versus 2 for changing the access code to 85 or something similar.

It should work fine... it emulates the M7310