Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by OKACHA

  1. OKACHA

    HIPATH 4000 v6 UPGRADE ISSUE

    HELLO; I have a hipath 4000 V6 (duplex / DSCXL2) as shown in the image .my question are: 1- how can I add Tapro STD for openscape CP400, CP600 phone set? 2- is it possible to upgrade the systeme to V11 with the DSCXL2 card or i should install an ecoserver; what about the other shelves 'LTU'...
  2. OKACHA

    Hi am trying to call office in different Pabx hipath 4000 and its response back on screen Do not disturb

  3. OKACHA

    Hi am trying to call office in different Pabx hipath 4000 and its response back on screen Do not disturb

    hi the do not disturb is activated ; to disactivate it from the phone go to the menu (he three horizontal line) then service menu>>> then interuption >> the do not disturb>> disactivate
  4. OKACHA

    LI1,HO2

    did you setup the correct static IP Configuration IP Addresse network mask default route VLAN ID
  5. OKACHA

    problem unify cp200 stuck on boot screen

    i have an openscape desk pjone cp200 ( HFA soft) stuck on screen "UNIFY" and not booting . is there any solution like DERT for openstage phone. besty regards
  6. OKACHA

    UACD power box (Lineage Power) for hipath4000

    HELLO . I have problem with the power box for hipath 4000 as shown in image , i'm wondering is it possible to buy a new UACD power box (Lineage Power) ? from Where? Any help to repair it or replace it. the rectifiers are working but no battery backup
  7. OKACHA

    SIP trunk configuration on hipath 4000

    HI #Moriendi WHERE CAN I FIND THIS Edoku IP Solutions . WOULD YOU MENTION THE LINK PLEASE
  8. OKACHA

    SIP trunk configuration on hipath 4000

    hello; could any one give me the required config (command line on comwin) to configure one sip trunk on hipath 4000 V6 , STMI4 ard configured with FCTBK=2 ( BCHL3550=20, BCHLSIP= 20 , BCHL3550=20) best regard Taha OKACHA
  9. OKACHA

    sip truk Aavaya ip office 500/ hipath 4000 V6 (STMI4)

    Hello I want to interconnect an Aavaya ip office 500 and a hipath 4000 V6 (STMI4) with sip trunk what config i would make on hipath 4000 , any one could explain how to config a sip truk Best regards taha this is a regen of my stmi card <REGENERATE-CGWB:LTU=4; REGENERATE-CGWB:LTU=4; H500: AMO...
  10. OKACHA

    Connecting OpenStage Key Module 15

    hello; i think that you should first use CHANGE-TAPRO:STNO=xxxx,STD=60; and then conect your module in your display the phone is detected as | [highlight #CC0000]OPENSTAGE 40 T[/highlight] | 0 | FF FF FF FF | | 0 | best regards okacha
  11. OKACHA

    ATTENDANT CALL FORWARD WHEN LAN FAILURE/ NIGHT OPTION FORWARD (NAVAR)

    HELLO; THANKS SBCSU I HAD TRIED STNOOS BUT IT DOSN'T WORK ANY OTHER SOLUTION. THIS IS MY ACSU CONFIG AFTER CHAGING AND TEST: <DISPLAY-ACSU:ATNDNO=3901; DISPLAY-ACSU:ATNDNO=3901; H500: AMO ACSU STARTED +--------------------------------------------------------------+ |...
  12. OKACHA

    ATTENDANT CALL FORWARD WHEN STMI4 fail

    HELLO EVERY ONE IS THERE WAY TO MAKE THIS FORWARD
  13. OKACHA

    ATTENDANT CALL FORWARD WHEN LAN FAILURE/ NIGHT OPTION FORWARD (NAVAR)

    HELLO EVERY ONE IS THERE WAY TO MAKE THIS FORWARD
  14. OKACHA

    ATTENDANT CALL FORWARD WHEN STMI4 fail

    please any help how to configure forword for attendent to a digital subscriber (SBCSU) when LAN failur occur for STMI4 [highlight #CC0000]LAN CONN. . . . . . . . . . DEF LINK SIGNAL ETHERNET . . . . NOT PRESENT[/highlight] <dis-navar; DIS-NAVAR; H500: AMO NAVAR STARTED...
  15. OKACHA

    ATTENDANT CALL FORWARD WHEN LAN FAILURE/ NIGHT OPTION FORWARD (NAVAR)

    please any help how to configure forword for attendent to a digital subscriber (SBCSU) when LAN failur occur for STMI4 [highlight #CC0000]LAN CONN. . . . . . . . . . DEF LINK SIGNAL ETHERNET . . . . NOT PRESENT[/highlight]
See more

Part and Inventory Search

Back
Top