Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by OhThatComputerGuy

  1. OhThatComputerGuy

    Radiant KDS

    SET RADVIDEO=TRUE SET RADVIDEOS=1,2 (OR WHATEVER THE DEVICE ID IS)
  2. OhThatComputerGuy

    Radiant KDS

    Few things first: 1. Are you licensed for Video? 2. Are you replacing a controller box or is this a new station? 3. Have you already done the Aloha Manager programming for Video.
  3. OhThatComputerGuy

    Radiant 1520 Terminal Issues

    You could try Key Services: http://www.keyservicesmw.com/ But no promises...
  4. OhThatComputerGuy

    CTRSVR not registering after new install ver 6.7.22

    If you do not run the setup with "Use Compatibility Mode" and select "Windows XP," you will get that error. Also, you will need to make sure you have installed the correct V++ versions as well...Also, I believe there is a version issue with 6.7.22. I would bump up to 6.7.28 or higher.
  5. OhThatComputerGuy

    POS Contracts

    Restaurants purchase the license to use the software, they do not actually purchase the software. Obviously, there are certain items that the resellers do not want you, the end user to know, but in the end you should be able to manipulate it to your heart's content. There are some resellers...
  6. OhThatComputerGuy

    suggestion for kitchen printers

    TM-U220's.
  7. OhThatComputerGuy

    Radiant 1520 Terminal Issues

    It is the motherboard and since NCR/Radiant manufacture their own terminals, you probably will not be able to just "buy" a motherboard. Really you would only be able to buy another 1520 and swap it out that way.
  8. OhThatComputerGuy

    Aloha EDC persistently going into Spool down.

    You need to check the EDC path on the terminals in the ibercfg.bat. It should be pointed to the fileserver\bootdrv\edc, etc.
  9. OhThatComputerGuy

    Aloha BAR FOH Move Item To Another Tab

    Split that item off to a separate check, then transfer just that check to the other employee.
  10. OhThatComputerGuy

    Aloha CC receipt problem

    There is a language code on the debit card that forces the data to use French. There have been instances where the card was setup to use French even though the card holder did not ask for it. There was an actual defect that was in version 6.5.17, but if it continues to happen then it has to do...
  11. OhThatComputerGuy

    ALoha pos - Refund from an old day

    Once the end of day has processed, you cannot change any previous day's sales data, other than labor. This would have to be an internal note on your books.
  12. OhThatComputerGuy

    Aloha Payperiod Parameters and Overtime Calculations

    Maintenance -> Store Settings -> Labor (Over Time Calculations) Maintenance -> Store Settings -> System (First Day of Week) If you cannot get to that section, then you do not have the necessary security rights. You may have to contact your reseller to grant you that access.
  13. OhThatComputerGuy

    Aloha Terminal PXE E53 Error on Startup

    No, the boot order has nothing to do with the software until you actually get to windows.
  14. OhThatComputerGuy

    remove hasp key

    You may still need to reinstall the hasp drivers for the new motherboard.
  15. OhThatComputerGuy

    Aloha upgrade instructions

    You also need to make sure that you run the vcredist_86.exe as an administrator. Also, run the update as the administrator, if you do not it will look like it all went through, but in reality it did not. You can also double check the debout.set located in the root of C. This will help you get...
See more

Part and Inventory Search

Back
Top