Recent content by ogulcan

Dear colleques, is there any way to make an mpls vpn "communucate " with a non mpls segment on the same wan eg e segment connectedto a different interface with no "vrf forwarding " configuration. Because during the migration i dont want non mpls eigrp networks to disconnect...

Yes,cef is enabled? do you have any idea why packets are dropped? thx.

Hi,my question is that why does ignore and drop packets increase on ethernet.We experienced 2 times crash because of that.but we cant find the exact solution ios upgrade did not solve. what could this be? thanks in advance. sh int FastEthernet1/1/0 FastEthernet1/1/0 is up, line protocol is up...

ok George, thank you for help again. I love this site & people helping each other. take care.

George, i guess i found the problem. According to your first message i surveyed the configuration again and again..i found the following. THOUGH i have a vlan 130 on 6509 my packets belong to that vlan are not entering the 6509 from that vlan interface.How?These vlan is also creted on an other...

George thank you for your detailed explanations but the packets are realy coming from the right interface; switch_6509#sh arp | inc 10.75.2.200 Internet 10.75.2.200 87 0008.7409.591a ARPA Vlan130 switch_6509#sh ip route 10.75.2.200 Routing entry for 10.75.2.0/23 Known via...

About the down configuration i can not make the pakets matched at list 105 go through tunnel 0 on cisco 6509. Altough rest is working fine they prefer the route given in static route. Under the needed vlan i have the command for source routing though...? route-map switch_6509 permit 5 match ip...

is it possible to make a cisco router take an ntp time from a windows 2000 ntp server. Though we followed all the steps for enableing ntp servis at win2000 server and check the availibility of the needed ports of ntp we could not realize a cisco router taking the ntp time. is it not...

Hi friends ; i want to tftp my crash files from 7500 router but they are hided in the directory...i see them all with sh command but can not see with dir command,that is why i can not get them for read. best regards.. sh bootflash: -#- ED ----type---- --crc--- -seek-- nlen -length-...

Time based dial back-up system problem I am trying to build up a time based dial back-up system but i am faced with a problem. Time based access lists(which i have to attach a dialer list) needs a word but,the required access list for a dialer list can not be a word,it should be a number.But i...

baddos thank you:)it worked.i did not try it...have a good day.

just for information for ones who have over cisco 3600 you may use following commands. dial-control-mib To specify attributes for the call history table, use the dial-control-mib command in global configuration mode. To restore the default maximum size or retention time of the call history...

Hi baddos, the output of "show int fast 0/0 " command is as following,it is 100 000 kbit actually.. And about the priority,i got some other routers configured like the mentioned above but their bandwiths are 100 000 kbs not 10 000 kbs. What i try to say is that ,if there were a...

jdel; i did what you said exactly; changed the speed manually ;100 the port connected the router,and the port of the router..but problem remains. Allied Telesyn Ethernet Switch AT-8024GB - AT-S39 v3.2.0 <No System Name> Login...

Hi, On a 3700 cisco router i got the following configuration on ethernet; interface FastEthernet0/0 no ip address no ip route-cache no ip mroute-cache duplex auto speed auto ! interface FastEthernet0/0.1 encapsulation dot1Q 10 ip address 10.1.222.1 255.255.255.248 ip access-group 105 in...