Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by nunney

  1. nunney

    IBM SNAP DUMP Analysis

    Hi all, can any one help with decoding/analysing IBM hardware SNAP DUMPS.I'm looking for a starting point ie where to find the reference material etc mainly RS6000 P & Z series.
  2. nunney

    Santricity & STK D173 Storage Array

    Hi I've got an STK D173 Storgage Array with 6 discs.1 has failed & needs changing.I'm assuming I need Santricity to connect to the array & remove the disc with the software before physically removing it. Does santricity have to be Host attached or can it be installed on a laptop.I'm then...
  3. nunney

    SUN SL8500 Handbot problem

    Does any one know if any 3rd party vendors are supporting these yet? I've got one that's out of warranty & the Handbot LED's are playing up?
  4. nunney

    DLT Drive Firmware

    Hi, any one know how to read the drive Firmware level using Net backup on a Sun L3500?
  5. nunney

    L5500 Robot Speed

    Hi I've got a ACS of 2 L5500's that have just come off of Contract to STK/SUN. I'm convinced that the Robotic Arms are running slower (when compared to my other S/390 attached) Does any one know of a way to check this?
  6. nunney

    L700e & 9840b's

    Hi I've got a problem with my L700e having trouble unloading tapes from the 9840b's.I've got two L700's linked with 9840b's in each.It seems as though the gripper can't pull the tapes out from the drives.On checking I'd have to say that the cartridge mech's are too stiff, any one seen this before?
  7. nunney

    STK 4480/90 Addressing on CU

    Thanks STKMAN, I should have known that!!
  8. nunney

    4480/90 Silo to Standalone or Scratch Conversion

    Problem: If you buy second user STK 4480/90 drives from the Second user market (Broker) how do you specify that you want a Standalone or Scratch Version? If you get a Silo Version how or what do you need to do to change it to a Standalone or Scratch loader type.Has any one got a procedure?
  9. nunney

    9480 C FSC's

    Hi has any one got a list of 9840C FSC's please, or know where I could get them.
  10. nunney

    STK 4480/90 Addressing on CU

    Problem: I've got a range of 4480/90 M22 Standalone & Scratch loaders with 4 Controllers.They are physically numbered by the Tape Op.s to support their numbering scheme.ie B20 to BXX Question: How do I relate a Drive or Drive frame to a Controller ie. when I enter Maint & select device how do I...
  11. nunney

    STK 9740 LMU Error's

    HI I've got two STK 9740's one of them is playing up. (Haven't got the Lib FSC's)but the ACSLS error log is complaining about: au_lh_response(1): LH error type = LH_ERR_LMU_FAILURE cell 0, 0, 3, 0, 0: Library error, LMU failure ONC RPC: csi_rpcuinit(): Unmapped previously registered RPC...
  12. nunney

    9310 Get Problem

    Bizare.. I'm seeing the same problem with my 9310/9840's.You mentioned changing the hands, so I'm assuming that when you did you carried out a Long IPL from the LMU?
See more

Part and Inventory Search

Back
Top