Hi,
CM6.2, HA pair.
Server B set to local domain NTP sources "tic" and "toc".
Both sources ping OK and query OK, and server syncs time fine.
Server A will ping both sources fine, but the query state button is greyed out, and NTP will not start.
running command line ntpdate -d ip_address reports...
Thanks,
Sys para feats all set as you show above
add hunt help returns 1 - 8000
Ch bcms login shows agents 2001 to 2012 registered and named
Ch hunt 60 shows test ext 2278 populated up.
Speak softly and carry a big switch
Mr Hamilton, by golly,
Good evening Sir, many years since we last spoke!
Hope I find you well. Many thanks for the reply.
FAC for agent login is #12
agent dials #12 ( from registered handset in split group 60 )
dial tone returned.
agent dials 2001 ( registered BCMS Login ID )
gets deny tone on...
yes you can.
If using ASA set a task to find&replace EC500 state. set EC500 state to disabled.
Set everything to EC500 N.
then go back and manually enable EC500 on the extns you want to have this feature.
Then make sure that your off-pbx sta's are set correctly and delete the ones that are not...
Hi Guys,
Cust is running CM6.2 with AACC contact Centre.
As they have AACC, there are no EAS licences on the platform.
There is a need for a simple system with a single DN for the nightly duty manager to login, so the CC has a single number to call if they need to access the Duty Manager.
So,
I...
I have a customer with a remote G430 gateway and MM710 PRI card in Tel-Aviv.
When I installed it I could not find a country code for Israel, so tried a few until I got one that got the circuit up.
However, the customer is now complaining of low audio and slips on the circuit.
_ The country code...
Hi All,
Anyone have a model trunk setting for ISDN 30 PRI for Israel?
Seems to be bog standard ETSI, but won't dial.
Should dialling be enbloc or overlap?
is signalling CAS or ISDN-Pri?
Any other gotcha's ?
thanks.
Speak softly and carry a big switch
Hi Brett,
Yes we have a TN2182B, but no Classifier.
I have already checked the sys cov settings and they are all OK.
I have got it working now, but with a bit of a work-around.
Created a 2500 set and made it abridged app to the Btn 1 on the X-Port 6408 DDI target.
Not sure why this fixed it...
Hi,
This is a Definity Prologix release V6i.03.1.230.8
An incoming DDI is directed to an X-Port extension with a cover path to a cover remote destination.
The forward works fine, but the caller does not hear any tones while the call progresses, just silence.
Also tried intercepting the...
Oh Well done!
I think you just hit the nail straight on the head.
It has a CPN prefix of 76 set, with total CPN of 7 digits.
As a Chinese Cellphone is 11 digits...........Opps.
Thanks
Speak softly and carry a big switch
Hi All, This has me completely foxed.
User has a 9620 station on a CM 6.1. Trunks are E1 with China Telecom
EC500 is all set up and works perfectly when another internal user call the station.
When an external caller rings the DDI, it appears to work but the Cellphone never rings.
Cellphone...
Hi,
This is on a CM 6.2.
IP Conference phone firmware load 1.4.3
Phone goes through startup routine and then sticks at "Running... App=1692_014000.bin"
They did work, but following a local power failure now stick at this.
Any ideas please?
Speak softly and carry a big switch
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.