Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by networkstudent

  1. networkstudent

    Knowledgenet Quality

    Hi, I've been using knowledgenet for a while, but not for CCIE but for CCNP, CVOICE & CIPT. At this level, i can tell you that they are state-of-the-art learning tools, i'm using the express product they have. They includes hands on labs that are really neat but if you expect exam crams, real...
  2. networkstudent

    How much Novell stuff is on CCNA?

    I think memorizing & understanding ipx encapsulations could help Jose Paez CCNA
  3. networkstudent

    Cisco Routers?

    Hi, It depends on how much you want to spend. If you wanna get on budget, cisco's 2501 found used on ebay should be a good start, it is cheaper to buy and to have because even the serial cables are cheaper and easier to make if you want to make your owns. The only handicap is that you'll not...
  4. networkstudent

    PoorBoys PentaScanner or Microtest???

    Hi Jonnyboy, If you want an usefull scanner, cheap and usefull i'll recommend these: For wiremapping, i can't imagine a better thing than Siemon's STM-8, is the hell of resistant and durable and still a very good tester, very usefull too. If you want something above that without spending your...
  5. networkstudent

    About Microtest MT350 and HP J2263A

    The following are the serial cable pinout for these two scanners wich are the same, and other info i hope any of you could find helpfull Scan--------pc or printer db9---------db9 1------------1 2------------2 3------------3 4------------4 5------------5 6------------6 7------------7...
  6. networkstudent

    HP Cable Test Set J2263A

    Hi Quickdraw, Okay, i'm not sure but i think the ac adaptor is 7.2 volts, but i'll check later, right now i don't have the scanner near me, but by the way, i think this could help you a little bit, the original external charger is very generic, i'll tell you what i can for you to buy new...
  7. networkstudent

    HP Cable Test Set J2263A

    Yes Quickdraw, i did, tell me what you want to know about the instrument so i can tell you, this instrument is exactly the same as microtest mt 350
  8. networkstudent

    Load Balancing on an ARN

    First of all Many Thanks Scot, Yes, one of the functions of a router no matter wich brand is load balancing, in nortel's BayRS there's a function called Equal Cost MultiPath (ECMP) but i'm not sure how to deploy it. Thanks again
  9. networkstudent

    Load Balancing on an ARN

    Hi and Thanks for looking!, I have 3 different sources of internet, and i would like to share the load betwen them instead of having to configure one network segment to use gateway 1 and other segment to use gateway 2, etc. to increase performance and fault tolerance I was thinking about doing...
  10. networkstudent

    Frustrated and Embarrassed With My Studies

    Glad to hear that Elija, By the way, if there's any thing i can help you to understand something about vlans don't be afraid to ask. Bye and my best wishes!! Jose Paez CCNA
  11. networkstudent

    CCNA HELP on Simulator

    It is very easy to configure 2 routers to ping router A from B, i'll try to explain. First, you gotta understand what a DCE or DTE means, normally, router acts just as a DTE device, and the DCE device its that one that gives the clocking as an example a modem, the computer communicates with the...
  12. networkstudent

    Frustrated and Embarrassed With My Studies

    oooooooooooooooooooops i've made a mistake, the last subnet is 192.168.1.224 with host from 225 to 238, boradcast 240 wich is the same number as the subnetmask, Sorry! Jose Paez CCNA
  13. networkstudent

    Frustrated and Embarrassed With My Studies

    If your problem is subneting, don't worry anymore, its as easy as it can be. English its not my native language but i'll do my best to explain some tricks, if your can't understand anything feel very free to ask me i'll be glad to try to re-explain. let's do it in one way first: you have the...
  14. networkstudent

    CCNA 640-607 Question

    Hi everybody, I've just taken the cisco CCNA exam (october 9) and passed it with 975, this is my very first time with cert, any of you know what's the next step after taking the exam? I only have the score printed, now what? Thanks for looking!
  15. networkstudent

    HELP with Microtest MT350

    Hi everybody and thanks for looking, I need the MT350 or MT310 (its the same cable as i know) printer cable pinout. and if there's any particular info about baud rate or any other serial parameter. By the way, i does not have the manual, so if any of you knows if there{s a way to share data...
See more

Part and Inventory Search

Back
Top