Recent content by netlife

Hi, Enable secret password configured with level 5 encryption. So anyone expectes that after RADIUS authentication user prompt will be seen on the telnet/SSH window then putting enable command the router should prompt for password set in the enable secret command. But this isnt happening and...

Hi, What is the difference between cisco VXR and non VXR Routers? What VXR interprets? TIA. Regards, Netlife

Hi, I am new to the LINUX world. I have a problem with a LINUX Telent server. The Telnet server is having Dual IPs, 1.107.108.x.x (LAN IP) 2. 97.1.1.x (IP ADDRESS for accessing devices) LAN----TELNET SERVER----HUB----NETWORK DEVICES All my network devices are in the 97.1.1.0...

jneiberger, You are right...no need to send http traffic to DNS server. Here I was just confused due to the fact that the DNS server is geogrophically somewhere else from where we want to access interenet.I had the dought that if I just could reach DNS server,I could access internet....just...

Hi KiscoKid, In sequence 10 when there is not SET parameter the packets will be routed by the routing protocol which is running in the background.In this case OSPF.OSPF will then route packets destined for internet to the required ISP. Also Packets can be routed to the required ISP by...

Hi, I am having two ISPs and I want to divert http traffic to to one perticular ISP.TO achive this I have designed a route-map which forwards the http traffic to a DNS server of the local ISP.Will this work? The route-map configuration is as follows, access-list 175 permit ip x.y.z.0...

Hi, I found that AT & T has given a bidirectional loop and both of us are recieveing the loop. As far as cabling is concern,the tx (Orange,Orange White---at RJ-45 Jack end) is connected to Rx of the ISP STM1 MUX. I am getting framing error on both the ends.I have used ppp encap on both the...

Hi, I am connecting router on both the ends of an E1 link. The setup is router-modem-----E1------modem-router. My serial interface of the router(Cisco3640)is physically up but the line protocol is down on both the ends. The E1 link is up and I am getting loop from the far end modem.On modem,I...

Hi All, One cisco 2950 is not booting it just going to the rmon mode.When I tried to use xmodem command to transfer a .bin file it gives me the following error, switch: copy xmodem: flash:c:\cisco\c2900XL-c3h2s-mz-120.5.2-XU.bin Unknown cmd: copy switch: copy xmodem...

Dear all, the config change detector process is not starting . Even after starting the process manuaaly it stops after few sec's. because of which no logs changes are traps across the network devices pleasse suggest ????

Hi All, If I span multiple vlans continuously on MSFC,will affect CPU utilisation of MSFC or what would are the possible implications. Thanks netlife

The router configurations are, R2# Building configuration... Current configuration : 1259 bytes ! ! Last configuration change at 14:53:27 UTC Sat Mar 2 2002 ! NVRAM config last updated at 14:47:53 UTC Sat Mar 2 2002 ! version 12.3 service timestamps debug datetime msec service timestamps log...

Hi All, I am having the following setup, Fa0/1 172.18.121.1 Eth 0 130.1.1.20 R1-------------------------R2---- | fa0/0 172.18.121.2 | 130.1.0.0/16 R1-cisco 2600 which is an internet router R2-cisco 1751 which I am using...

Hi, The boson router simulator does not support RIP V2 yet. netlife

Hi All, How to check the bandwidth of the leased lines on the router.One of our leased line bandwidth got upgraded yesterday. netlife