Recent content by Netadministrator

Thank you 392 and dagwoodsystems for sharing your expertise on this. This is the total system layout. Carrier 1 Slot 0 Processor CKE5 Slot 1 024 TDL Slot 2 408 GS/LS-MLX Slot 3 408 GS/LS-MLX Slot 4 100D/CSU/DSU-U Slot 5 408 GLM-U Carrier 2 Slot 6 024 TDL Slot 7 024 TDL Slot...

Magix 2.1 V8.0 I have 024 boards in slots 6 & 7 008 boards in slots 8 & 9 & 11 Merlin Messaging in slot 10 Can I replace the three 008 boards with 024 boards.

Are you connecting the crossover cable to the MM switch? This should be number 1 in the stack. I have four 3300’s with two crossover cables connected to switch 1 (The one with the matrix module) and it works. It really shouldn’t make any difference unless you have configured the ports on the...

I have a problem with users disabling Windows Firewall on their laptop computers. I have to keep the users in the Administrators group on the laptops because of some applications require it to run. This allows them more rights than I would like to give them. The Power Users group will not allow...

The best solution is BES hosting. http://www.mailstreet.com/ http://www.exchangemymail.com/

Same here - I have an HP LaserJet 4200TN with a JetDirect 615n card that lost its connection to the network and isn't showing any lights. I removed the card and reinstalled it and turned the power back on and it still doesn't have either light (10/100) on. I also installed it in the other EIO...

Problem Solved!!! ScoTTel and rhislop were right about the DB9/DB25 adapter. I found eight of them lying around and started going through them until one connected. They were not marked in any way so it was a shot in the dark. Thanks to everyone who contributed. Stars for everyone!!

I’m sure that it is COM 1. It only has one serial port. I tried changing the port numbers but that didn’t help. The site setup instructions indicated that the baud rate should be set at 2400. It was also the default setting. I have never connected to the board before now. This new processor was...

I am having the exact same problem. I have WinSPM - Release 7.0 running on Windows 98. The 355A/F adapter connected to a DB25/DB9 converter connected to the COM Port of a Gateway Desktop PC. I have tried connecting a regular CAT5 and a CAT5 crossover cable from the 355A/F adapter to the ADMIN...

I am having the exact same problem. I have WinSPM - Release 7.0 running on Windows 98. The 355A/F adapter connected to a DB25/DB9 converter connected to the COM port of a Gateway Desktop PC. I have tried connecting a regular CAT5 and a CAT5 crossover cable from the 355A/F adapter to the ADMIN...

MMANTHA, this site provides manuals, guides and instruction sheets for the Phaser 740 in .pdf format. http://www.officeprinting.xerox.com/perl-bin/product.pl?product=Z740&page=sprt

Great news Holdout. Now start printing those Christmas cards!!! Only three days 'till Christmas. Happy Holidays

I had the same problem and installed a new Clutch, Second Transfer Roller - Part Number 116-0993-00 and the problem was solved. The part cost me $26.75. You will have to remove the paper feed assembly first. Then remove the black plastic cover over the circuit board by removing the screw on the...

I had the same problem and installed a new Clutch, Second Transfer Roller - Part Number 116-0993-00 and the problem was solved. The part cost me $26.75. I purchased the part from: Brian Lewis Vice President/Service Manager Total Laser Care, Inc. 770-449-8400 770-449-0038 Fax...