Recent content by mywayray

Quick question- Can I simply go to LD 11 and chg the Type from 2018 to 3904? Thanks

I'm having an issue with CPND on the CS 1000- The environment is Option 11 rel 25.40 B with a SL1 tie to a CS 1000 rel 5- Calls from the Station on the CS 1000 display Name & Number on the Station on the Option 11- However call from the Option 11 only display 'H' and the extension number (no...

Reusser- Thank you for your reply- Was able to use a maint. phone found that SPRE was 11 not 1 Was then able to enable the TTY 0 Again thank you-

I relocated an Option 11 rel. 25.40 to a new facility- It would seem that the TTY's are disabled- I receive output from the switch but I'm not able to login I'm also not able to determine if a Matin. phone is provisioned on the switch- I tried the 191 to log into a digital station and 19...

Thank you for the reply- I was hoping that I didn't have to build an entry for each DID-

I have a new span (ISDN PRI) being cut today- The PBX has a 4 digit dial plan and 'The Boss' ordered 10 digits of DNIS from PSTN- My brain is tired- can someone give me a quick idea to, on the incoming route, strip the first 6 digits- Thanks

John- Thank you for you reply- Standard Call _______________ DCE Frame 45 (82 bytes) was captured at 21:33:03.779 with no errors. LAPD: SAPI = 0, TEI = 0, C/R = 0 Frame Type = INFO N(S) = 73, N(R) = 39, P/F = 0 NISDN: Protocol Discriminator = 8 (Q.931) Call Reference...

I have a problem with QSIG Call setup messages from an Option 61C running Succession 4.5 to a system that uses Dialogic DS-1 boards- The issue is; In the setup message of a forwarded call, the setup contains the number and name of the forwarding party- This is a normal event- However the...

One other thought- The PSAP will receive the '2 way' billing number and other location info from the CO unless the site has a system of sending the info itself-

MitelInMyBlood- It would seem that over the weekend the enhanced QSIG package was installed- Now not only does the Nortel folks see the original ANI when the call is extended by the Operator or Auto Attendant but the Mitel stations receive a refresh of the ANI on Alert - prior to this the...

MitelInMyBlood- Thank you for all your help- I'll be back on site next week- Operator transfer from the Mitel to the Nortel station was my issue- Station to Station both ways seems to be OK- I'll have the Mitel Eng run the Mitel trace utility also mention the enhanced QSIG question- I'll post my...

MitelInMyBlood & jneiberger Thank you for your replies To answer jneiberger's question The Nortel is running 25.40B MitelInMyBlood- I connected a protocol analyzer to the span & found there are 3 elements in the call setup all reporting at 0x1C- The first is the name of the calling party, the...

jneiberger- Thank you for your reply- We were able to tie both PBXs together- The only outstanding issue is with QSIG Transfer- The Operator on the Mitel receives a call and extends it to the Nortel, only the Operators extension in displayed- There doesn't seem to be a info element in the D...

iptuser- Thank you for your reply- From the Nortel side I will be using CDP to a route list index to point the calls back to the Mitel (station to station & to PSTN) What I'm looking for is something I can pass along to the Mitel Engineer to A) Data Fill to build the DS-1 B) Data Fill to build...

MitelInMyBlood- Again, thank you Unfortunately the numbering plan is not consecutive The existing office has numbers throughout the range, and the new office will pickup the unused numbers (no one wants to tell someone that they have a new number) So the Engineer will need to route one number at...