Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by mynus

  1. mynus

    MICS 6.2 --> BCM50 Interface?

    Great, thanks for the response. At the MICS we are already on a PRI, so I'm assuming the enabler we currently would work. I'm going to be bringing a vendor in on this, but I've heard conflicting reports of what is and isn't possible here.
  2. mynus

    MICS 6.2 --> BCM50 Interface?

    I've heard conflicting reports of this actually working without buying $12k in VOIP licenses. I have a base office with an MICS 6.1 with about 85 users. I'd like to get a point-to-point T1 to interface this office with a new remote location. At the new location I was told I can put a BCM50 and...
  3. mynus

    Site-to-Site routing issue

    So if I make my "central" IPSEC endpoint a Cisco router with that IOS version or higher, I can setup tunnels to my remotes, and have my remote users connecto a Pix behind said router, THEN they will be able to access those remote sites?
  4. mynus

    Site-to-Site routing issue

    Correct, I basically want to be able to VPN into Site A, and function as if I were on my network. That means, I want to be able to access a web site I have running out at Site B, by connecting to Site A and having my protected traffic routed through that network. I've seen it working well before...
  5. mynus

    Site-to-Site routing issue

    I can, I'm just trying to avoid confusion first. I think this is a routing issue, that's why I was asking what the usual steps were. I've got these two pix's running, but when you connect with a VPN client to one site, you can t get to the other. I want to be able to access Site B by connecting...
  6. mynus

    Site-to-Site routing issue

    Simple question that goes with the basics of VPN's I'm sure. Pix 506 (sute A) to 515 (sute B) setup, tunnel works just fine. I have users connecting to Site A, but now I need them to be able to access Site B while using the Site A connection. Shouldn't this just be automatically possible since...
  7. mynus

    Fax Server with Norstar MICS 6.1

    I've got an MICS 6.1 using PRI. I'm trying to find out if anyone has interfaced a Brooktrout card with a similar setup. The end goal here is to have a block of DID's setup to point at a fax server which can email faxes to the user assigned to a specific DID. I'm planning on using FaxServe, but I...
  8. mynus

    Incoming Only

    Awesome thanks!
  9. mynus

    Incoming Only

    I've got a weird one. This is an MICS 6.1 using a PRI and a Callpilot 150. Recently I found that half of my users weren't getting Caller ID properly on incoming calls via the CLID. So, I went through every extension, re-assigned their lines to their phones, and enabled Caller ID via the 'Telco...
  10. mynus

    506e access group conflict? in interface outside, HELP!!!

    When you say client, is this just one person that will be working with your system?
  11. mynus

    506e access group conflict? in interface outside, HELP!!!

    You could make this a lot easier on yourself and just setup a dynamic map to allow VPN clients to connect individually.
  12. mynus

    Routing problem or Gateway Issue?

    I'm using two 506E's for a site to site tunnel between our two networks. Here's an example: Site1: 192.168.1.X Site2: 192.168.2.X Pix1 Outside: 172.100.100.1 Pix1 Inside: 192.168.1.1 Pix2 Outside: 172.101.101.1 Pix2 Inside: 192.168.2.1 Site1---[Pix1]....(VPN)....[Pix2]---Site2 Both sites are...
  13. mynus

    VoIP through NAT/PAT

    PAT is actually noted by Cisco's release notes not to function at all with VOIP. Using common sense it's kinda obvious anyway, but NAT should work just fine, as the outgoing/incoming streams for H.23X should be masq'd and forwarded, not port translated.
  14. mynus

    Creating VPN tunnel on PIX-506E

    It's sort of hard to walk someone through a setup because everyone's VPN is different. First off, as a warning, the Pix PDM wizards kinda suck....really bad. There is a new version of the PDM called ASDM that is only available with the Pix 7.0 Operating System. Unfortunately that OS doesn't work...
  15. mynus

    DID's CLID showing '1234 to Prime'

    Funk yeaw. That was it. Thanks atcom.
See more

Part and Inventory Search

Back
Top