Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Murksel

  1. Murksel

    Analog lines in 1 Pool

    905 and so on are the end digits of the phone numbers. We have destination code 9 or 8 doesn't really matter in this case and pool shouldn't either. Pool A is used for other tests. :)
  2. Murksel

    Analog lines in 1 Pool

    Just" another configuration issue. ;o) Setup is the following, BCM50 Rls 3, 3 analog lines and 3 sets (there are 2 more IP and 2 digital ones as well but leave them out for now). We have: Lines 61, 62, 63 DNs 234, 235, 236 Public ... 905, 915, 916 We set up Pool B for those 3 lines. Pool B...
  3. Murksel

    Replacing ringtone with MoH?

    Hi guys, is it possible to replace the ringtone with MoH? We tried to set it up using CC: 1. Greeting 2. Transfer We hear a short part of the MoH (< 1 sec) and then the phone rings and caller gets the ringtone. We want caller never to hear the ringtone - go it working on Cisco System where...
  4. Murksel

    1120/1140 on BCM400

    Hm, BCM was powered down over the weekend and after restarting and connecting up the phones again, everything is fine. Hm, I did some restarts last week and they never helped ... weird ...
  5. Murksel

    1120/1140 on BCM400

    Registration is Enabled and NEtmask and Gateway IPs are correct as well.
  6. Murksel

    1120/1140 on BCM400

    DHCP is set to Enable - IP phones only. Tried static IPs as well, still not happening.
  7. Murksel

    1120/1140 on BCM400

    Ok, problem is that thos phones keep saying that the server is unreachable. BCM 4.0 is just an out of the box unit, Rls 4. Cold reset has been done already. (No chance of Level 1 reset with a 400, is there?) Tested a softphone as well - no luck. Did a direct test - IP phone directly into LAN...
  8. Murksel

    Cisco Switch with BCM

    Any idea for a test config or advise on how to configure Cisco 3560 switches for use with BCM (PCs will plug into phones). I need to know QoS settings and any other special settings for Nortel equipment. The PCs will be in the data VLAN and the phones will be in a Voice VLAN.
  9. Murksel

    1120/1140 on BCM400

    I heard that the 1110 is BCM50-only - does this apply to the rest of the 1100-series? Can find any docs on that.
  10. Murksel

    BCM50b + 2x DSM32?

    Was going in the wrong directions there. BRI doesn't matter, you got 12 digital stations in the BCM and get another 32 with the DSM which results in the given limit for the BCM50 > 44 digital stations.
  11. Murksel

    BCM50b + 2x DSM32?

    Hi just a question rgarding the BCM50b. If only the 2 internal BRI trunks are to be used for lines, can we put 2 x 32DSM's into expansion chassis to support a total of 76 digital extensions?
  12. Murksel

    Audiofiles on BCM 400

    The files are fine.
  13. Murksel

    Audiofiles on BCM 400

    Hi guys, got a problem with a BCM 400 Rls 4, all latest patches are installed. When playing MusicOnHold or listen to custom messages (AA or CC) it plays normal - stops - suddenly starts to play the file with immense speed (highpitched sound) then playing it normal for a while and begins again...
  14. Murksel

    RCC Errors

    Hi guys, got different problems here while trying to set up Reporting for Contact Center. FIrst I used to get errors that SQL Server 2005 wasn't install, it was but I uninstalled and reinstalled it. RCC installation finished - reboot and now running the RCC Database Installer Utility (DBI) and...
  15. Murksel

    CCR, AA - live lines needed?

    Hi guys, found this thread - well the analog loop is set up pretty quick - but is there any way to try this with a BRI module or with a BCM50b?
See more

Part and Inventory Search

Back
Top