Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by mucka

  1. mucka

    Filter problem in ver 3.2.2.2 8600

    Thanks guys but all is now well , waited a short while and they then semed to work ok !!! Strange. Thanks anyway Mucka
  2. mucka

    Route summerization

    Hello Guys , we have a large network of 14 X 8600,s with a large overhead of routes using ospf . Does anyone know of any documents/white papers on route summerization that may help me with this . Thanks in anticipation Mucka
  3. mucka

    Filter problem in ver 3.2.2.2 8600

    Hi guys I have set up successfully a series of filters on Passport.The problem is trying to let one lan communicate with another ie: desination of 10.10.14.0/24 to source of 10.10.28.0/24 forward, to enable pc,s on one side (28) to print to a printer on 10.10.14.0 network.Very simple and...
  4. mucka

    optivity switch manager ?

    Hello guys , we are running the above switch manager ver3.0.0.0 when upgrading firmware to our BPS,s we put in our bossXXXX.img and works a treat ,BUT how do we upgrade the diag file ie: boss3005_diag.bin. ?? We tried it in the image field but doesnt work and tried it in the "450/mix stack"...
  5. mucka

    BPS stack loss of QOS

    Thanks biv343, can anyone suugest a later stable code ver that may correct this web browsing fault ?? Thanks again Mucka
  6. mucka

    BPS stack loss of QOS

    Hello all , has anyone seen this fault ,very infrequently we have a loss of "Trusted Ports " after a power outage ,resulting in bad voice quality . We do not have a config loss , just Qos advanced ->interface conf->Trusted ports loss. The vlans & ip etc are all ok . Has anyone else seen this .We...
  7. mucka

    8600 default route

    Hello Hungryhouse thanks for the reply yes we need to keep our default route 0.0.0.0 nxt hop X.X.X.X . Then certain sources in our large routed network need to get to the internet via a seperate isp, so yes FROM 192.168.0.0/16 nxt hop Y.Y.Y.Y .We have 400 vlans and routing via 13 X 8600,s so all...
  8. mucka

    8600 default route

    Hello all , we have a default route on our main passport to our internet connection. it is obviously "destination 0.0.0.0" "next hop X.X.X.X" we would like to be able to set another static route BUT on source address instead of destination. I have heard other vendors can do this but I am not...
  9. mucka

    8600 hangs !

    As it happens both 8600 & contivity where on the same power circuits but now we have moved contivity elswhere. We do not seem to have any issues since so hopefully it was a one off . Thanks for all reply,s and advice Mucka
  10. mucka

    8600 hangs !

    Thanks once again guys , around the same time we had a contivity box crash that connects directly into the passport and it took the hard drive out , coincidence ?? I have since been checking the "show log file tail" for clues but no "malloc errors". are there any checks/tests I can do to...
  11. mucka

    8600 hangs !

    Yes , thanks for the info the .000 file gave the fol error message at 4am sat morning: error code xxxx can,t malloc pkt memory 32 <np> IP-RIP eroor iprx: out of memory.(Whatever that means!) This repeated umpteen times ,and we do not have rip enabled ! foll this message there was nothing till...
  12. mucka

    8600 hangs !

    Thanks for the reply Anthonyanderberg my collegue says the utilisation was not unduly high .It was not passing traffic through to servers etc. We use e series on this box. What particular bugs did you experience with 4.0.2.1. ? Thanks again Mucka
  13. mucka

    8600 hangs !

    Hello Al , any help please we recently had a problem were our main 8600 froze .It is a fully polulated box with many stacks/servers/main frames , and other 8600,s hanging off it.We couldnt telnet or device manage it although we coud ping it , unfortunately my collegue didnt have a console cable...
  14. mucka

    VRRP without SMLT ?

    Thanks for the onfo guys, the answer to the last question is they are feeding 10 other switches (5 each side of a rack enclosure)that then feed blade servers !! Mucka
  15. mucka

    VRRP without SMLT ?

    Hello all , we have 2 passports with IST but instead of having SMLT to 5510 stacks ,our customers want 2 seperate 5510,s one from each passport.This is because of the 6 MLT limit per switch. I have done this with the same vlan on each 5510 and the same gateway HOWEVER it reports a ip conflict on...
See more

Part and Inventory Search

Back
Top