Recent content by merios

THats a great idea .... and would do so for most sites. Although in this case, I was thinking of the Company Christmas party, where all employees would be at a restaurant! ... no internet access there unfortunately! cheers

I want to be able to transfer calls waiting in a skillset to an external number and I want to be able to toggle this functionality remotely from a telephone. I am about to configure an Intelligent overflow rule to transfer calls to an external number (rule 2 in overflow rule table in call...

i am trying to connect a 3640 to a 1751, the 3640 is the gateway for a microsoft netmeeting voip client and the 1751 for another. Does the terminating dial-peer have to be a pots voice port? or can I successfully make the above call - netmeeting to netmeeting? (I currently use "debug voip ccapi...

Has anyone done implemented the TDM cross connect feature using a Cisco 3640 or similar to consolidate 2 pri lines (1 into a PBX and another into another 3640)? From what I have read, it seem a PRI (CCS) cannot be used to digitally cross-connect this setup. anyone?

either the card you are using is not a VWIC card and/or is not in the right port (can only be used in port 2) or you have the wrong IOS version installed.

Does anyone has any suggestions with regards to multiple call ringing between 2 sites? I have 2 PABXs, one at each site which have a DDI pool serviced by a single ISDN30e @ site A. Which connects to Site B over TIE trunks to Cisco Routers (one at each site) and makes use of a co-ordinated...

cool thanks .. I will try that .. ..btw. I dont have a call logging company .. I manage the PBX on my own, and have connected the TTY port to a Solaris Conserver to capture the CDR .. which I have set up some scripting to present it. cheers

I am trying to get rid of the 2nd and 3rd lines of each CDR record (ie. all & and Zeros)... any ideas? ----------------------------------------------------- N 004 00 7826 T121008 10/08 11:47:37 00:00:02.0 A90800001001 &...

I have a 6509 which I have configured for VMPS. When I configure port membership to dynamic to participate I have the problem that on my large network, some users might decide to patch in a hub on that port. When I tested a hub connected to that dynamic port, I patched in 2 nics both known in...

thanks Fritz, I can't access the switch at the mo'.. will have to go to site to connect up .. to show that I have actually created a PTY .. funny thing is that, it shows /pty/ptty02.S as opposed to /pty/ptty01.s as previous. why is that? I will post CFN once I get the info... cheers

rlogin -l CPSID XX.XX.X.XXX Done! /pty/ptty02.S is not defined in SL1 Database PDT in Progress. Please Wait....Done! Anyone have any ideas?

ok .. sounds good to me... so should I be able to see spare DN's based on the new range ? BT?. no, worse - c&w!

I have extra TNS .. but I thought I would only need as many as I was going to configure to a set. What is meant by expanding the channels? yes I am in the UK. cheers

I have a 30 channel pri which I have asked my telco to configure up a second range of DDI numbers to go down this channel. What changes do I need to make to my option 11c?

This is what I get when I trace the call... .trac 0 8167 ACTIVE TN 005 0 00 02 ORIG 001 02 DID RMBR 110 2 TERM DN 8167 TDTN 0 SLOT 16 PTY SLOT 16 DIAL DN 8167 MAIN_PM RING AUX_PM TALKSLOT ORIG 16 TERM 16 EES_DATA: NONE QUEU CAD CALL ID 0 346 ---- ISDN...