Recent content by MERIDIAN11C

is the same using the 8 ACOD or dialing just the cdp

acewarlock this is the TN TN 002 0 00 01 TYPE 3903 CDEN 8D CUST 0 FDN 7990 TGAR 1 LDN NO NCOS 4 SGRP 0 RNPG 0 SCI 0 SSU 0080 LNRS 16 XLST SCPW 1234 SFLT NO CAC_MFC 0 CLS TLD FBD WTA LPR MTD FNA HTA ADD HFA GRLD CRPD STSD MWA LMPN RMMD SMWD AAD IMD XHA IRA NID OLD VCE DRG1 POD...

yes i can i see the names and also i have callpilot with NMS working fine

and this is the CFN DES CALLPILOT N1 512 ADAN DCH 11 CTYP MSDL CARD 01 PORT 1 DES JILO USR PRI DCHL 1 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC ISGF PINX_CUST 0 ISDN_MCNT 300 CLID OPT0 CO_TYPE STD SIDE NET CNEG 1 RLS ID 4 QCHID YES...

thanks johpoole this is the route REQ REQ: prt TYPE: rdb CUST 0 ROUT 11 TYPE RDB CUST 00 DMOD ROUT 11 DES JILO TKTP TIE NPID_TBL_NUM 0 ESN NO RPA NO CNVT NO SAT NO IDEF NET RCLS EXT VTRK NO NODE DTRK YES BRIP NO DGTP PRI2 ISDN YES MODE PRA IFC ISGF SBN NO PNI 00001...

well is Nortel to Cisco - Cisco to Nortel using this DCH DAN DCH 11 CTYP MSDL CARD 01 PORT 1 DES JILO USR PRI DCHL 1 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC ISGF PINX_CUST 0 ISDN_MCNT 300 CLID OPT0 CO_TYPE STD SIDE NET CNEG 1 RLS ID 4...

the 8 digit is the ACOD and 4460 the ext. also i have CDP with 44 but is the same goes busy i mean forwarding 84460 and 4460

thanks acewarlock i have two Op.11 using PRI with QSIG when i try to forward to the other system goes busy this is the TN TN 002 0 00 01 TYPE 3903 CDEN 8D CUST 0 FDN 7990 TGAR 1 LDN NO NCOS 4 SGRP 0 RNPG 0 SCI 0 SSU 0080 LNRS 16 XLST SCPW 1234 SFLT NO CAC_MFC 0 CLS TLD FBD WTA LPR MTD...

call forward using PRI is not working any idea ? thanks

many many thanks to all for answare thanks

hello someone has the list of all the patch and what is the meaning of each patch patch from 22.08 till 5.0 thanks

display your partition table

Johnpool as comment the people of this system has accustomed as SCR you know i mean, ringing all the MCR at the same time

thanks Jhon poole REQ: stat 3 00 = UNIT 00 = IDLE (3902) 01 = UNIT 01 = IDLE (3902) 02 = UNIT 02 = UNEQ 03 = UNIT 03 = IDLE (3904) 04 = UNIT 04 = IDLE (3902) 05 = UNIT 05 = IDLE (3902) 06 = UNIT 06 = IDLE (3902) 07 = UNIT 07 = IDLE (3902) 08 = UNIT 08 = IDLE (3904) 09 = UNIT 09 = UNEQ...

only one think i have SCR on all the 3903 and 3904 sets but if a set MCR works fine but it was working as SCR 3 months ago the 4.5 as an DEPLIST with 121 patch on september i install the last DEPLIST with 161 patch i guess was the new DEPLIST, but i dont know which one is the mising patch...