Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by MartinR82

  1. MartinR82

    OWA on SBS 2003 Not working

    well i guess you wouldnt unless you had a time machine to go back and find out why, but i thought i would ask the question anyway.............................?!!? On a slightly less sarcastic note, thanks for replying. No, I havent attempted a restore as I have nothing to restore from and the...
  2. MartinR82

    CCM Installation woes!

    Im sorry to see so many people still having problems even after reading my walkthrough. I should have mentioned that I installed it in VMWare and not directly onto a machine. The host OS was Windows XP. My walkthrough should work for non MCS (non generic) platforms..... I tried the other...
  3. MartinR82

    OWA on SBS 2003 Not working

    Hi all I have SBS 2003 running and OWA has been fine. I had to unplug the machine whilst I sorted out the rack so I shut it down as normal. Once it has powered back up OWA has stopped working!!! I have looked in IIS manager and all the files from the exchange folder have gone? So when i browse...
  4. MartinR82

    Cisco IP Softphone CIPC

    Hi Guys Thanks for the replies. I have changed it to use the MAC of my PC, now it wont connect at all. Someone has mentioned that we need licenses for the CIPC and use CTI ports? Anyone shed any light on that? Thanks
  5. MartinR82

    Cisco IP Softphone CIPC

    Hi All Could someone give me some pointers as to why when more than one person is using CIPC on the LAN, the other person gets booted off and then is logged into extension mobility with the number of the person who just got booted off? Any ideas?
  6. MartinR82

    Port Forwarding

    sounds like you need to upgrade the IOS. For your own safety I would change your telnet password and perhaps think about changing your SNMP community string as from your config anyone whos a little bit dodgy could telnet on to your router and perhaps run DDoS attacks from it, or at least try and...
  7. MartinR82

    CCM 4 intallation fails

    follow my guide here.. http://www.tek-tips.com/viewthread.cfm?qid=1140145&page=4
  8. MartinR82

    VPN 1700 problem

    forgive me if i have the wrong end of the stick, but you will need to configure another IPSec tunnel from site B to C would you not? And it looks like B only has a crypto map for site A?
  9. MartinR82

    Setting up a vpn via 2 cisco 837 routers

    crypto isakmp policy 1 hash md5 authentication pre-share group 2 crypto isakmp key Make1up address <peer address> crypto ipsec transform-set set1 ah-md5-hmac esp-des (this is assuming that single des is appropriate for your needs) crypto map vpn-traffic 10 ipsec-isakmp set peer <peer...
  10. MartinR82

    2801 problem, weird

    try pinging with the DF bit set, if this fails then you know that the carrier does not allow packets with the DF bit set to 1 and the way around this is to setup a GRE tunnel between the routers as GRE traffic has the DF bit set to 0 by default and then all in tunnel traffic can have the DF bit...
  11. MartinR82

    CCM 4.1(3) on with less than 1 GB RAM

    yeah, modify the registry before installing CCM to make it think that it has 1GB of RAM. There are plenty of guides on installing CCM on non MCS
  12. MartinR82

    I got a big problem when I am installing the ccm4.0 on genetic pc

    Follow my post in this thread word for word and you should have no problems.. http://www.tek-tips.com/viewthread.cfm?qid=1140145&page=3 If you still have issues then dont use the 2000.2.7u upgrade, use an older one, like 2000.2.5
  13. MartinR82

    Cisco 1720 slows and then jams

    Definately need to see the config.
  14. MartinR82

    WIC Card installation

    Provided the current IOS you have supports a WIC 1T then when you boot it back up you will have a Serial0/0 interface ready for you to configure, it will most probably be admin down though.
  15. MartinR82

    General questions about CCM

    He right you know... http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a008009428e.shtml
See more

Part and Inventory Search

Back
Top