Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by limitbreak

  1. limitbreak

    Meridian Mail won't boot Install tape

    Thanks for the reply, I did not change the baud to 1200, I was watching the tape drive for activiy, but didn't see any. I did try the level 2 pswd, but to no avail. There is no SEER printer on site, unfortunately. I am going to take another SCSI cable, tape drive if I can find one in the...
  2. limitbreak

    Meridian Mail won't boot Install tape

    Hello, I am having an issue here...I am currently working on an Option 11C R23 with Card Option Mail R11. This switch was apparently here already when the new tenants moved in. I was lucky enough to find the PBX password (not Lvl 2 however) written under the kb. I cannot however find the...
  3. limitbreak

    answer dn MICS 3.0

    Thanks for the quick response. I tried that, but this software won't let me create multiple target line appearances.
  4. limitbreak

    Programming speed dial on NBX phones

    A little late in this response, but I was browsing threads. Could you have the user log into NetSet with administrator rights, go to button mapping on telephone, changes desired autodial/speed dial key to another feature, say Release. Save that change, then have her go back and change button to...
  5. limitbreak

    answer dn MICS 3.0

    Hello all, I have a customer with an MICS 3.0 *shudders*. Here is the situation: I have an extension 232, the bossman. Three other phones, 221, 225 and 247 all have Answer DN keys of 232 on them. Now, a call will come into the Target Line 169, DID for extension 232, and extension 221...
  6. limitbreak

    2250 BLF

    Hello, I have a customer with an Enhanced BLF module hooked to a 2250 console. I have this configured as Enhanced. The receptionist can press a loop key, dial 4, for the 400 - 499 extensions, and the BLF displays them. The problem I am having is when someone goes off-hook on...
  7. limitbreak

    "Cannot Continue" General Delivery

    Thanks for the replies, General Delivery is turned on. We did assign mailbox 120 to the main telephone, as a temporary fix. We have re-installed Voicemail, and the problem was fixed for a few months, but is now a problem again. I think the fix with the other mailbox will hold them...
  8. limitbreak

    "Cannot Continue" General Delivery

    Hello all, One of our customers has an issue with a BCM. BCM 400 3.6 Build: 2.2c When attempting to access the General Delivery mailbox for message retrieval, upon logging in, we receive the message: "Cannot Continue" "Exit" I have reset the password on this mailbox, and change it, but...
  9. limitbreak

    Fiber Remote Mutli-IPE SYSTEM MONITOR

    *UPDATE* Well... After extensive troubleshooting, this problem still persists. We have double-checked dip switch settings on System Monitors, checked dip switch settings on the Fiber Remotes, swapped of Fiber Remotes on local and remote sites. Our next course of action is to attempt to replace...
  10. limitbreak

    CFWD to LD + Acct Code

    *UPDATE* Had the end user try the ACOD for the route. Since there is only one route on this PBX, there are no others to try. Yielded the same results, no go.
  11. limitbreak

    CFWD to LD + Acct Code

    Hello all, I have been having problems with a customer unable to call forward their set to a Long Distance phone number. This site uses Account Codes set up via circuit provider. The customer claims this is not working, upon using a * or # sign after number, then account code...
  12. limitbreak

    Network Dialing (4 digit)

    *UPDATE* Figured I'd update the resolution, since a lot of people browse these forums for answers. The problem ended up being the 1FB phone line that was used for the FastRAD. This was setup in the same pool as the Point to Point channels. Obviously, when I Remote Set, and tested, this 1FB...
  13. limitbreak

    Fiber Remote Mutli-IPE SYSTEM MONITOR

    Hello all, I have a customer with an Option 81, here is the rundown of equipment. Bldg A Core 0 and Core 1 IPE 20 0 and 20 1 Fiber Remote Multi-IPE unit Bldg B IPE 4 0 and 4 1 Fiber Remote Multi-IPE unit My question is concerning the System Monitor cabling. We are...
  14. limitbreak

    BCM 400 Modem

    Thanks for the reply. I will give this a shot next time I am up there.
  15. limitbreak

    BCM 400 Modem

    I have a customer whom has a BCM 400, but there wasn't a modem installed on it. We installed an NTAB9968 FRU Embedded Modem into the unit. The BCM Unified Manager does not list it when trying to configure it, and it will not answer a call to it. I was wondering if there was anything special...
See more

Part and Inventory Search

Back
Top