Recent content by lifeisloud

you can do this through the "my phone app" on the utility server - assuming it is configured. https://xxx.xxx.xxx.xxx:8443/MyPhone/MyPhone it needs to be the IP address of the utility server not the phone it also depends what you want to do - sorry i have no experience of Cisco phones

Hi Henning here is the response i got from Avaya "This issue seems to be a known issue in CM 5.2 and in order to resolve patch 17402 should be applied. This patch contains also all fixes available in SP 17294". I would like to think this is fixed in the latest SP. Play it loud

hi All, I hope one of you can help me, I am installing 1xP, IPS and AES (4.2.1) CM 5.2 (17250) s8300 G700 and although i have everything working internally i can't get the 1xP client to dial to an external number. scenario 1 logon to 3206 using 1xP and i can choose deskphone and make calls...

I'm trying to get a rule to work in outlook 2007, basically i have 1 exchange mailbox and and another MAPI mailbox. so i basically have 2 "inboxes" when i run rules in the exchange mailbox it all works very well, however when i create a rule in the MAPI mailbox it does not run automatically, if...

Hi, Any ideas how i should program a route pattern to incorporate the extension number being sent out to the network for extension billing purposes? I have extension 750 which needs to call any number in the world, the route pattern it goes over is determined by ARS. the route pattern has a 4...

Yes, been using it for a week now, on CM3.1 with presence and video only crashed once but i think that was my laptop. Its a shame Avaya didn't "re-invent" the call bar view as it looks just the same as V5

Rockspop, Thanks a million downloaded the patch (using IE7) and it named the file correctly with a .gz and without the [1] which in turn enabled me to run the "update_unpack" correctly. Thanks again

Hi Rockspop, no when I do ls -l it shows the file without the .gz going to have another go and see what happens thanks for the quick response, i will let you know

Hi, no reason code but below is the output root@SIPserver> update_unpack 03.1.018.0-10013.tar unpacking file 03.1.018.0-10013.tar.... updates/03.1.018.0-10013/ updates/03.1.018.0-10013/ccs.conf.tpl updates/03.1.018.0-10013/config.xml.template updates/03.1.018.0-10013/event_config.xml.template...

Hi All, I'm Running SES 3.1 (SES03.1-03.1.018.0) and want to load the latest patch 10013. I have downloaded the tar file to the server but what is the next step? I did an "update_unpack" in /var/home/ftp/pub/ but it went through the process and then failed..... any help is always appreciated

1.5.3 is available on the support web site. it fixes many issues Andy

hi, I need to use an external NTP server. does anybody have a public address for one? I have found one but when i configure the time server settings on the 8300 it fails, (I have done a traceroute to the name from the 8300 and it resolves to the IP address so i have connectivity)and i have...

it is used to carry -+48v as the aux cable used too, for power fail transfer relay panel/power for attendent console. there is a document that explains all on the support web site but i cant find it!!!!! Andy

hi, not sure about the xmobile tones. to get the correct number format you need to "ch sys fea" and go to page 8 and change the following to look like this National CPN Prefix: 0 International CPN Prefix: 00 Life

Hi Shandy11, Just installed mine this week and had the same problem. in the trunk group form on page 2 do you have "numbering format unk-pvt"? if so I changed mine to "unknown" and changed the "ch public-unknown table" and entered my extension length, extension code, trunk group and CPN length...