Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by leo74

  1. leo74

    Cisco CATOS -- use MRTG to monitor traffic only on one interface

    great.. thanx
  2. leo74

    Cisco CATOS -- use MRTG to monitor traffic only on one interface

    is it possible with MRTG to obtain traffic only on one interface?.. i am not sure what parameters i would have to pass in snmpwalk... Switch model CATt6509 OS - CATOS Thank you
    • leo74
    • Thread
    • Replies: 3
    • Forum: Cisco
  3. leo74

    Installation TACACS+ on linux

    yeah.. i have to go with tacacs.. but thanx
  4. leo74

    Installation TACACS+ on linux

    could anybody guide me in the right direction how to install TACACS+ server on linux. (the instructions would be very helpfull...) i would like to setup cisco swithes and linux server with AAA authentication. thank you
  5. leo74

    Can't pull ip w/ intervlan routing.

    command 'ip helper address x.x.x.x' should do it for you. x.x.x.x is your dhcp server ip
  6. leo74

    Port commands

    it is simple... once you are connected to the switch just type 'en' (input the password), type 'confit t' (this will put you to a configuration mode...) for example you need to configue port 1. type 'int fastethernet 0/1' now input 'no shut' command, hit 'ctrl + Z', type 'wr mem' or 'copy run...
  7. leo74

    How to - PXE Boot

    Thanx Glen, something like that is what i need.
  8. leo74

    Blade server usage.

    I inherited the blade server. Therefore I am very limited in the direction of ‘blade server for your application’, just need to find the use of it. Since I do not have a second box I am dismissing the clustering. I agree configuring each blade server on the same box as a cluster node would not...
  9. leo74

    Blade server usage.

    Alright… here goes the humor…Jkupski - wearing the server around your neck is very "elaborated" even for 80s. I am sure someone will do it… but that is not the question I was asking about. I have no need in the long list of types of servers… just spare it. I need more technical information...
  10. leo74

    How to - PXE Boot

    let's say I have 10 worstation in the same location.
  11. leo74

    Blade server usage.

    ...and what would you do with it... ...describe..
  12. leo74

    How to - PXE Boot

    I suspected that I would not be able to reboot the workstation with PXE card.... unfortunately... I guess i need to setup wake-on-lan… Because if the workstation is unresponsive or blue screened I will not be able to use shutdown.exe What is the procedure for the wake-on-lane? Is there any...
  13. leo74

    Blade server usage.

    Hello everyone, I have a simple question. What would be the best usage of a Blade Server (Dell PE 1855) I have server handy and I also have a couple of SANs available... Any suggestions?
  14. leo74

    How to - PXE Boot

    Hi, I would like to find out how I can reboot the workstation (Dell GX270) remotely using pxe card. I enabled the ‘network boot with pxe’ and ‘fast detect’ on the workstation in BIOS. What command or utility can I use to do so? Any ideas would be greatly appreciated. Thank you,
  15. leo74

    Jobs start at random time.

    Have anybody had any problems with jobs starting at some time when it is not specified. My Friday’s full backups begin at random time. The job is set to run at 11PM. But for the past couple of weeks it has been starting previously at 4:18AM and 1:08. And after that the job would begin at 11PM...
See more

Part and Inventory Search

Back
Top