Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by lastation4

  1. lastation4

    ACD Queues

    Another odd symptom is that the ringback is incredibly soft when it does happen.
  2. lastation4

    ACD Queues

    I've got an odd behavior going on. After the initial FFRT, the call disconnects about 30 seconds afterwards. What could be causing this to happen? Another odd behavior is when calls come in from "internal" trunks from different foreign DNs from other systems, they apparently don't get any...
  3. lastation4

    Connecting CS1000 to Cisco 2921 and routing SIP to POTS

    Yep telling me about the transcoder in the cube helped me fix it. Thanks!
  4. lastation4

    DCH lamp showing Yellow

    Relevant Cisco Configs: network-clock-participate wic 0 voice-card 0 ! ! ! voice service pots controller T1 0/0/0 cablelength short 110 pri-group timeslots 1-24 service mgcp interface Serial0/0/0:23 no ip address encapsulation hdlc no cdp enable isdn switch-type primary-qsig isdn...
  5. lastation4

    DCH lamp showing Yellow

    This is all well and good, but this is not a PRI2 card. I need a T1 not an E1 interface. None of these configs are clearing the yellow DCH light. I've tried the Cisco to Nortel config as well provided by Cisco, and that seems to not work either. EDIT: I'm also using a TMDI card.
  6. lastation4

    Connecting CS1000 to Cisco 2921 and routing SIP to POTS

    So I've got an intersting issue to deal with here. I've got a SIP trunk that comes into my cisco 2921. I need to route calls coming down that SIP trunk to the CS1000. I think this is done with a dial-peer pots but so far I have no success. Any tips?
  7. lastation4

    DCH lamp showing Yellow

    Alright I'm back after a long hiatus on this thing... I've got everything turned up but I cannot for the life of me get the DCH to establish to my Cisco 2921. Clock is Green, so that's not it. EDIT: I get a message on turning on the DCH: DCH055 DCH: 106 RLS CTS DOWN TIME: 18:50:21 8/06/2025
  8. lastation4

    Can't get T1 DCH to establish

    This is a TMDI 1.5 DTI/PRI card.
  9. lastation4

    Can't get T1 DCH to establish

    Correct. That's what I'm trying to setup here is primary and secondary clocks. It seems like on the second card, the DCH will not establish and channels 1-23 are in a MBSY state.
  10. lastation4

    Can't get T1 DCH to establish

    Yeah i got it to work, but am having the same troubles adding another TMDI card. Same issues, CC RED RED ALARM on the second card. Now i'm having issues getting the second card to recognize the other main clock?
  11. lastation4

    Can't get T1 DCH to establish

    As the title says, I'm having issues with getting my DCH to establish. I get a myriad of errors such as the following: DCH055 DCH: 51 RLS RED ALRM TIME: 21:55:08 5/07/2024 TIM000 22:00 5/7/2024 CPU 0 XMI001 4 0 6 TMDI TMDI102 TMDI 4 0 6 DCH: 51 DISABLED (TMDI 4 0 6 SYS DSBL)...
  12. lastation4

    Digital Set will not ring IP set

    I actually discovered the issue, and it was exactly what you described. The DSPs were misconfigured. Everything rings everything now, thanks for y'all's help. You can close the thread.
  13. lastation4

    Digital Set will not ring IP set

    I tried changing out TNs which is why the TN being traced is different than before.
  14. lastation4

    Digital Set will not ring IP set

    These are M1 Option 11 boxes. > ld 80 TRA000 .entc 200 0 01 00 100 gotr .18:28:39 25/06/2024 VTN 200 0 01 00 KEY 0 MCR MARP IDLE KEY 1 NUL IDLE KEY 2 NUL IDLE KEY 3 NUL IDLE KEY 4 NUL IDLE KEY...
  15. lastation4

    Digital Set will not ring IP set

    Here's the output of the LD 80 trace of the digital set. .11:12:17 24/06/2024 TN 000 0 05 00 KEY 0 MCR MARP ACTIVE TN 000 0 05 00 IPMG 000 0 ORIG TN 000 0 05 00 IPMG 000 0 KEY 0 MCR MARP CUST 0 DN 6969 TYPE 2008 SIGNALLING ENCRYPTION: INSEC TERM NONE TDTN...
See more

Part and Inventory Search

Back
Top