Recent content by ksphoneman

Losing the HDD on the VS is not a good thing. It will be hard to find a replacement at 40MB. The system will continue to function until the next power failure, but you won't be able to administer any changes, as you only have the data the is loaded into memory to work with. The RES HD command...

ERR-026 Floppy disk error; read / write error occurred Replace floppy If you are have a running system and the HDD is "unloaded", you might be able to "RES HD,FM00" instead of "LOA FILE" Some of the error codes are in the Commands Manual Vol 1, page 11 General categories of errors are listed...

Is the Nortel inserting the ARS access code (9) before sending the call to the Fujitsu? In the Nortel DMI for the BARS/NARS route (LD86) the DMI should insert 9, before passing the call to the Fujitsu.

The Cisco to Fujitsu trunk group can be any TLT (Trunk line type), If your trying to use VACDN routing, the DSTNO would be an access code to either dial a trunk group access code or to send the call to AAR (Automatic Alternate Routing) using AARLC codes and ARS routes. The ARSDM can be used in...

Vacant DN is similar to call forwarding. It uses a DSTNO prefix to steer the call to a particular trunk group. The feature is available on all Fujitsu 9600 systems. UNASSIGNED DN TRANSFER TO ANOTHER PBX DESCRIPTION This feature makes it possible for a station user to transfer a call to an...

DMS-100, since I've seen very few Fujitsu systems have the optional QSIG software features installed. As long a ISDN CO Pri Basic service was installed on the Fujitsu, you have the DMS-100 capability. The worst part of the migration is when the migrating users want to keep their extension...

The name usually does not display until the call is connected. For the Fujitsu to send the name to the Cisco, verify the ARS route to the Cisco has the NAMF feild set to "1" and the SVP,2,180 is set to a "1" CHA ARSR, ARSTB, POS, [FRL], [PTNNO],,,,,,,,,[LARF],[CMPF],[CDNFG],[TON],[NPI],[NAMF]...

The name from the Cisco must be all upper case letters. Also check the box on the Cisco Gateway , T1/ISDN trunk, check the box to enable "Send extra leading character in DisplayIE" The Cisco version of the configuration is here...

Thanks for the reply Texeric, No, the new AD will be completely separate. (New company after a merger) Nothing from the old domain will be present. New AD DC and new Exchange server. Thanks, Mike O'Neil

Searching for a procedure and second opinions for moving an existing 5.2 MAS with Exchange 2010 (working) to a new Active Directory Domain. The new domain has a new Peer directory server and a new Exchange 2010 CAS. It seems as though I'll need to treat this as a new installation. I haven't...

To see which ports are voicemail DIS VMSPT Check these ports for dial tone and verify they can be answered. Most voicemails will still answer the call, with out integration data The Fujitsu uses SMDI, check the I/O port status DIS SYSS If any of the ports are "Offline" use RES IO,DCUXX to put...

Programming is identicle accross all of the platforms. The only difference with the smaller systems (US and LE) is which card slots were available. What is the error code you get when you build the trunk group? Also note that ISDN trunk groups have an extra command. You'll build the two TG...

Delete all of the programming related to the second cabinet. IE Delete any phones, trunks, etc that are in the second cabinet. The EN would start with 0008. Delete the packages that are installed. (DEl PKG). Delete the shelf. (DEL SHF) Save changes. Power down the cabinets. Pull the BNWU0B...

Either the Agent ID is already signed on to another telephone, or the extension is appearing on another telephone. To sign on via the Intellicenter Supervisor, the Agent screen needs to have the Agent's extension number in the Agent configuration screen. The Agent login will also be blocked if...

When the ISDN PRI D channel is built in the ASS ISTRK command, the "MS" feild is for either Master or Slave. If the Shoretel is the Network, then set this parameter to Slave. I have gotten this to work with Cisco <-> F9600 as DMS100; to allow the name and number to pass between the two...