Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by Krul72

  1. Krul72

    Avaya G450 S8300 Failure

    AvayaRedTech, I performed the 'nvram init' and reconfigured the IP. I can access the CLI of the G450 but getting hung up on SNMP3 when accessing the web site. I havent done anything with the S8300D. Although I can access it using the admin account, I can only access BASH and the web site. I...
  2. Krul72

    Avaya G450 S8300 Failure

    So I did get lucky with Admin\Admin01. I was able to login to the CM and found the error - there is no license. I get this message roughly 30 minutes post boot. It seems like it cant find the license and then gives up. This switch was part of a survivable failover that no longer exists. I...
  3. Krul72

    Avaya G450 S8300 Failure

    So I dont have any passwords for the S8300D. The other company outsourced the support and the guy that use to support the system quit. I know I have to call Avaya but is it worth it if the card is bad? Or should I replace the S8300D? Is installing similar to the CS1000 where the system board...
  4. Krul72

    Avaya G450 S8300 Failure

    You are correct. That's exactly what it says. I was thinking it would have said it after the S8300 but that's what I get for thinking.
  5. Krul72

    Avaya G450 S8300 Failure

    It is a S8300. No letters after it.
  6. Krul72

    Avaya G450 S8300 Failure

    Hello, I received an Avaya G450 with a S8300 card from a sister business. I was hoping all I had to do was plug it in. Wrong. I have a solid red light on the S8300 and show faults states "Primary Controller Not Found". I can connect to the Services port on the S8300 and ping it. Does the...
  7. Krul72

    Siemens Hipath to Cisco ISR 4331

    Hello, I have a Siemens Hipath 4000, software v.6 that I'm looking to integrate with a Cisco ISR 4331. We were planning on running an E1 from the Siemens to the ISR and route calls as we switch over to Cisco UCM. Does anyone have experience with this type of migration? If so, is it possible...
  8. Krul72

    CS1000 Not Loading

    Awesome. Can you tell me what software I need to download? I dont know how to read the version number and match it up to what's on the Avaya site.
  9. Krul72

    CS1000 Not Loading

    Hi Firebird. Yes the number on the silver dongle matches.
  10. Krul72

    CS1000 Not Loading

    Hello, I received a CS1000 from an online provider for our lab. I was not sent licenses or software - just hardware that was suppose to have been configured. Of course, I cannot get the switch to boot to a prompt. To make it worse, the company will not support the switch and refuse to provide...
  11. Krul72

    M3904 no power

    This has been fixed. It was a wiring issue between the 66 block and the jack. Most likely loose punchdowns. Thank you for your help and Happy New Year.
  12. Krul72

    M3904 no power

    The TN is Card 2 Unit 0. So I used ENLU 2 0. I'm a little nervous to do anything physical to the switch. This is a small emergency dispatch center with two seats - now one. Im screwed if I lose the last seat. I think the card has 16 ports.
  13. Krul72

    M3904 no power

    I did LDIS 0, found the port listed, and then ran ENLU "Card" "Unit". Reran LDIS 0 and the Unit was not listed. The problem I have is that the phone location is in Eastern Europe and I'm working with the local tech who has less experience than me - which isnt much. And since this is a secure...
  14. Krul72

    M3904 no power

    Thank you. I have tried ENLU and reenabled the TN; however, this did not change anything. I believe it was locked out since the switch didnt see the phone for more than 24 hours. If I plug in the phone, will I at least see lights flash no matter whats going on with the switch?
  15. Krul72

    M3904 no power

    Happy Holidays to all, I use a Nortel Meridian Option 11C Mini with M3904 phone sets. I have one phone that will not power up - no lights, nothing. I swapped phones and cabling, made sure the power was good, but the issue remains at this seat whereas the equipment from this seat works at a...
See more

Part and Inventory Search

Back
Top