Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by klowndog420

  1. klowndog420

    hidding password

    That is what I thought. I am waiting for a response from someone I used to work with about this. We had a user complain that her VM password would show on the display. Whateve change was made it allowed for a display (i.e. internal calls, the number that was just dialed) but after the connection...
  2. klowndog420

    hidding password

    I thought there was something in CLS that could be changed to not allow the digits to display. I swear I had this issue at a previous location with Lyrix VM attached. This will bother me now because I can't remember what I did to fix it...
  3. klowndog420

    LD 32 FDLF

    thats what i thought after i did a few and saw the response i got back from the switch. These are just phones for new users that dont start till mid Jan. I'm bored and I was looking for something to do. Thank alot and a safe and Happy New Year to you all!!
  4. klowndog420

    LD 32 FDLF

    I was looking through the books and could not find an answer. I installed several 3904's today and they are lacking the lastest firmware on disk. How many can be done at one time on an individual basis?
  5. klowndog420

    greeting

    What would you like to happen when the recep forwards a call to vm? What should the caller get.
  6. klowndog420

    2250 Console

    The M2250 attendant console is connected to the Meridian 1 through two digital ports (primary and secondary) with three additional ports for powering. I have only ever seen it connected to a switch on a dedicated 25 pair cable.
  7. klowndog420

    LPK?

    I have used this feature when someone had multiple lines associated with their phone and didn't want to bother with hitting the key of the ringing line, they just wanted to pick up the phone. Incoming Ringing Line Selection With Incoming Ringing Line Selection enabled, when the user goes...
  8. klowndog420

    Octel Voicemail

    Good morning all. I know this might be a little off forum topic but I could not find any info about it. I am using telnet to dial into my Octel and was wondering if anyone knew what the window settings are for 800x600 resolution. I open telnet and dial in but all of my info seems my be strewn...
  9. klowndog420

    Helmsman 4.3 setup

    Wow!! That was perfect! Thank you very much M1!!
  10. klowndog420

    Helmsman 4.3 setup

    Well like I said, the primary ones come up (IPE, Succession 3.0, etc.) but now that I am looking for work, some opportunities have come up and I wouldn't mind using helmsman to look up other things (Call Pilot, CCMIS, MerMail, Symposium CC server, etc) that employers are looking for and since I...
  11. klowndog420

    Helmsman 4.3 setup

    So I went ahead and tried that. I added 2 new folders to helmsman 4.3. disc1 and 2 and copied bothe collect files to each folder. It still does not bring up all of the NTP's. It does bring up the primary ones I am concerned with looking at though.
  12. klowndog420

    Helmsman 4.3 setup

    Well I was able to find two other launch icons that did not carry over in the install. They are in the files I created when I copied the discs onto my hard drive. The first one opens the pdf files I am looking for (IPE, OTM, Sucesion 3.0, etc.) and the other opens the pdf's that after the...
  13. klowndog420

    Helmsman 4.3 setup

    I found that in the other posting but it does not bring up all of the docs. I am able to see symposium, mermax, mermail and call pilot but the other docs (OTM, succesion 3, etc.) do not come up. I was able to verify that they are in the same folder as the other docs but just don't show in the...
  14. klowndog420

    Helmsman 4.3 setup

    I went looking through the other post and found some info in regards to lockups and such but I am looking for some further assistance. I was succesful in installing the program but I seem to be stuck with Helmsman finding the pdf files. I get the error that no collection was found in c:program...
See more

Part and Inventory Search

Back
Top