Recent content by kings23

I'm curious if there is a method to remote desktop into a xp pro computer on a completely different LAN that is hooked with a modem and analog phone line with number? The computer I would be doing the support from would be on a high speed access (DSL, Cable, Verizon, Wireless, etc) I'm wanting...

I have two identical PE 2400 servers currently in a test enviornment with 2K Server set up with RAID 5, 2GB RAM, and 3 primary partitions C:(boot) E:(Application Data), and F:(Storage Data). Both of these will be sent to a seperate office and will used as domain controllers for Active Directory...

I already have different scope mappings configured on the two Cisco 1700 series routers that connect the two sites. For example, NT is using 192.168.1.1 and 2.1 scope and I've added .3.1 and .4.1 to use as a new scope for another domain. Will this scenario work or do I still have the potential...

Two sites using NT4 now. Can I add a seperate 2003 domain with a DC at each site and configure new users, new DNS/WINS, and new DHCP schema without affecting the NT4 domain and authentication? I may phase out NT4 after testing or possibly keep it running along with 2003. Should the 2003 domain...

Currently have two sites using NT4 for authentication with one domain. Default gateways for two sites are 192.168.1.1 and 192.168.2.1 and both sites are connected via T1 to ISP where firewall is located. I'm getting ready to install new 2003 servers in each site to begin the process of setting...

I'm wanting to do a FRESH install where all BIOS, ESM Firmware/Drivers, and Perc 2/si Drivers/Firmware are back to their lowest versions so I can update after I have an OS installed. Currently the BIOS is A09 and both ESM and Perc 2/si drivers/firmware are updated with the latest/greatest. I've...

I building a PE 2400 with the Perc 2/si RAID controller and 5 10k 18GB SCSI drives. I need the RAID 5 set up for redundancy but I'm looking for the right solution on creating the correct containers. I've just been testing it with different scenarios and currently I have it like this: I went into...

Does anyone know how to audit network users when accessing an excel file from a network share into a .txt file or something? I need to track users who access this excel file throughout the day to determine who is looking at it. Network is Windows NT 4.0 and I can see the users who have the file...

Does anyone know how to audit network users when accessing an excel file from a network share into a .txt file or something? I need to track users who access this excel file throughout the day to determine who is looking at it. Network is Windows NT 4.0 and I can see the users who have the file...

I have a Fujitsu Stylistic 2300 Pen Tablet with Win 98se installed. It has external 3.5 floppy and external USB 2.0 CD-ROM attached. I have a good image of the hard drive with a good install of 98se that I can keep reverting back to. With windows up and running I install the USB cd-rom so I...

I finally got it. I don't know why I didn't understand AirCon's first reply. I was trying to apply that device driver to the autoexec.bat file???? I don't know why. I can now see D:\ and things are looking sweet. Thank you AirCon and edfair. You two were a great help. I owe you. Thanks Kings

When I boot to floppy with w/ cd-rom supported I get: OTI-91x ATAPI CD-ROM Device Driver Device Name MSCD001 No Drives Found, Aborting Installation AIC-6260/6360/6370 ASPI Manager Then it shows: The diagnostic tools were successfully loaded to drive D: Device Driver not found 'MSCD001' No...

I tried this and it just says bad command or file name. I tried it a bunch of different ways but not luck. Everything works great until that last stop with the CD-ROM driver. Any help would be greatly appreciated. Thanks Kings

I have a Pen Tablet with an external Floppy that works fine and a USB 2.0 CD-ROM connected that I'm trying to use. Here are my steps: FDisk and create new partition then format C:Boot with Win 98 boot disk w/out cd-rom support A:\format C: /s/q to transfer system files A:\Sys C: to make C:\...

The CD ROM doesn't have to be E: as long as the hard drive is just one partition on C does it? When the boot disk runs it shows that the CD ROM is enabled on drive D and I get to the 98 setup screen on the cd as I can hear it spinning. It just craps out after I click Enter to go to the next...