Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Recent content by jwil320
-
Clocking on controllers cards cisco 2851 ISR
Finally figured this one out. The ISP was looking for individual clocking on each T1. So the clocking has to be configured for independent clocking. controller t1 0/0/0 clock source line independent channel-group 1 timeslots 1-24 I had to do this on each controller and now everything is ok... -
Clocking on controllers cards cisco 2851 ISR
My ISP said that each T1 should have its own clocking. -
Clocking on controllers cards cisco 2851 ISR
Doing that made my other controllers start getting errors. T1 0/0/0 is up. Applique type is Channelized T1 Cablelength is long gain36 0db No alarms detected. alarm-trigger is not set Soaking time: 3, Clearance time: 10 AIS State:Clear LOS State:Clear LOF State:Clear Version... -
Clocking on controllers cards cisco 2851 ISR
Serial0/0/1:1 is up, line protocol is up Hardware is GT96K Serial MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 112/255, rxload 128/255 Encapsulation PPP, LCP Open, multilink Open Link is a member of Multilink bundle Multilink1, loopback not set... -
Clocking on controllers cards cisco 2851 ISR
I am having som Slip Secs errors and Errored Secs show up on one of my controllers and was wondering how to stop them. The ISP says nothing is wrong on their end and they see no errors in the mux. Here is the out come from sh controllers T1 0/0/1 T1 0/0/1 is up. Applique type is Channelized... -
-
Catalyst 3560 ACL's
I pinged from 100.2 to 1.233 and got destination unreachable I pinged from 1.233 to 100.2 and got the same thing Then I tried pinging from 1.234 to 100.3 and got destination unreachable. then again from 100.3 to 1.234 and got the same thing. When I applied the ACL inbound the above pings... -
CCNA WannaBee - Log in Prompt - 2900XL
router>en router#conf t router(config)hostname switch switch(config) -
CCNA WannaBee - Log in Prompt - 2900XL
Change the name of the switch to switch -
-
Catalyst 3560 ACL's
I created a test VLAN100 and used the existing VLAN1 and created 2 different access-lists. 1st ACL I created was access-list 101 permit ip host 192.168.100.2 host 192.168.1.233 access-list 101 permit ip host 192.168.100.3 host 192.168.1.234 access-list 101 deny ip 192.168.100.0 0.0.0.255... -
Catalyst 3560 ACL's
Sorry about that VLAN 9 is our voice database. And pretty much everything needs to be able to talk to this vlan. Basically I don't wan't any other traffic allowed other than the traffic specified above. You your saying in order for this to happen the acl's should be applied outbound instead of... -
Catalyst 3560 ACL's
I have just purchased a new 3560 for my company. This is brand new out of the box. I have written up some access-lists and I was just wondering if they would work correctly when put into production. Here is what I have so far. I basically want to know if I have the traffic allowed in one VLAN do... -
Pix 515 Site-Site with NAT (Newbee)
what are you connecting a network or just a host to host- jwil320
- Post #2
- Forum: Security, hacker detection & forensics
-
Can Ping But no HTTP
Sorry that is a /24 not 25- jwil320
- Post #2
- Forum: Security, hacker detection & forensics
