Recent content by justatad

Just in case someone is looking for the answer on this one. I figured it out. In the situation aforementioned everything should work fine - however, if it doesn't make sure that your users have the ability to log onto the ISA Server (i.e. their accounts are not restricted to certain...

Hello, I am basically in the same situation as stated above. I have an ISA Server that requires authentication on http traffic that goes through port 80. I have went through the directions that real audio gives, but this doesn't work b/c the initial request that real player makes is through...

Here is what my latest problem is: - I have a domain set up for my internal network. (domain 1) - I have a domain set up for my ISA Server Array. (domain 2) - I have set up trusts between domain1 & domain2 as follows: >>domain1 does not trust domain2 >>domain2 trusts domain1 I would like...

Thanks Joe. The installation was smooth. I didn't dare try an upgrade. It seems like every time I've tryed to upgrade lately I've had tons of problems and at least 1 call into the M.S. tech support (Exchange 2000, etc.). See ya. Tad

Hello, Just wanted to let you guys know that I tried out the Nexland Pro800turbo router. I think that this would be fine and dandy for the simplest of networks, but if you are planning on having more than one IPs on the external NIC then the Nexland Pro800turbo router is not your choice b/c it...

Just in case anyone else is looking for solutions like we were on this topic I have found the following software solution. However, it isn't cheap & I was hoping that ISA could handle this function: RainConnect http://www.rainfinity.com/products/rainconnect.html If anyone knows of other...

Thanks Joe. Actually I figured out what my problem was. Just FYI if you accidently install IIS (left it unchecked) on your ISA Server. This causes problems. Especially if you are proxying off of port 80. ISA is running smooth now. Tad

Just wondering why if I have 2 servers configured practically identically. 1 is ISA Standard, 1 is ISA Enterprise. Why the Enterprise server will not publish or proxy me? While the Standard works fine. I know there could be a million and 1 reasons for this issue, but is there anything special...

I need to set up two ISA Servers (in 1 array) for fault tolerance (if 1 server goes down the other takes over). Could someone step me through this? If not, are there any good articles out there on this? Does anyone have any advice on some common mistakes that should be avoided?

I need to set up the servers to do (bandwidth) load ballancing between the 2 ISA Servers. I have 2 differnt T1s as my ISPs. Could someone step me through this? If not, are there any good articles out there on this? Does anyone have any advice on some common mistakes that should be avoided?

I need to set up the servers to do load ballancing & fault tolerance on 2 ISP connections. My assumption is that I need to have 3 NICS on BOTH ISA Servers. NIC 1: Internal Network NIC 2: T1 No.1 NIC 3: T1 No.2 Do I need 3 NICs on both servers, or just 1? If I just need 3 NICs on 1 server...

I have configured our current (standard edition) ISA Server. I am planning on upgrading to ISA Enterprise Edition & I want to configure 2 servers as 1 array. Could someone step me through this? If not, are there any good articles out there on this? Does anyone have any advice on some common...

Thank you. --- Here is a look at the Crystal formula (without parameters): {x.abc} in ["0", "1", "2", "3"] Here is the way it would look if I just wanted to enter based on 4 parameters: {x.abc} in [{?parameter1}, {?parameter1}, {?parameter3}...

I am trying to set up a report that will be used with Crystal's Web Viewer (Active X). In this report I would like to select multiple values per perameter (pop-up window in the viewer). Is there a way to add multiple values (either in the creation of the report, or the end-user entering in a...

Thanks a lot for the advice! One final question: You mention that I should create a table and inflate it. Could this be done in access? Do you have any code on this (sql or visual basic)? Or any general ideas on how I should approach inflating a table? Thanks again!