Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by jumper4000

  1. jumper4000

    Simple routing setup on a Cisco 3640?

    thanks for all your advice. I guess there was problem with my IOS. Now I can ping bewteen the two networks. I will let you know how combining the 2 T1 lines using cef will go tomorrow.
  2. jumper4000

    Simple routing setup on a Cisco 3640?

    they are both primary. We'll be using Cisco Express Forwarding to combine the two into one 3 meg line.
  3. jumper4000

    Simple routing setup on a Cisco 3640?

    this is for now the only router in our environment, so we'll use whichever one you think is the best one and easiest to setup. For now I just want the computrs from the two networks to be able to ping each other. Thanks
  4. jumper4000

    Simple routing setup on a Cisco 3640?

    Hi, I have a Cisco 3640 router (that's been killing me) and I want to setup very basic routing between two FastEthernet interfaces and two serial interfaces. This is my setup: I have one network (63.165.170.0/24) connected to FastEthernet0/0 I have another network (10.10.10.0/24) connected to...
  5. jumper4000

    Can't ping or access Ethernet interface

    no, it doesn't really change. at least not that quickly.
  6. jumper4000

    Can't ping or access Ethernet interface

    I've tried all that. tried from another pc. tried all the other interfaces (there are 4 in total). also tried half as well as full-duplex. all with the same result.
  7. jumper4000

    Can't ping or access Ethernet interface

    pinging 127.0.0.1 works just fine. As suggested before, I even took out the cable from the router, plugged it into another pc, setup the other pc with the same ip as the router, and I'm able to ping both ways. so it's gotta be something with the router.
  8. jumper4000

    Can't ping or access Ethernet interface

    yes interface is up and so is the protocol. gateway on the pc is set to 10.10.10.1. When I do a show arp all i dont see the pc.
  9. jumper4000

    Can't ping or access Ethernet interface

    I removed the config completely, and started fresh with a crossover cable. the routers IP on e0/0 is 10.10.10.1 and the computer's IP is 10.10.10.10. I still can't ping them.
  10. jumper4000

    Can't ping or access Ethernet interface

    yes, the same exact cable. I took it right out of the router and plugged it into the pc, and I was able to ping.
  11. jumper4000

    Can't ping or access Ethernet interface

    I was able to ping the other pc with no problem. That was a good idea though. At least now I know, the problem is isolated to the router and its configuration.
  12. jumper4000

    Can't ping or access Ethernet interface

    I'm gonna go buy a crossover cable tomorrow and try that too. Also, I have tried the other interfaces as well with the same result (i don't know what's wrong with this thing). Here's the result of show int e0/0: Router#show int e0/0 Ethernet0/0 is up, line protocol is up Hardware is AmdP2...
  13. jumper4000

    Can't ping or access Ethernet interface

    No personal firewall. even windows firewall is turned off (i did try both my desktop and laptop). I still can't ping it or tftp or anything. Is it possible that since there's no access-list present this router by default blocks every bit of traffic?
  14. jumper4000

    Can't ping or access Ethernet interface

    Thanks for your suggestions, but everything checks out fine. -Right now I'm using Cat5e straight cables (i have tried many ohters) -I am definitely connect Eth0/0 (have tried the other interfaces as well) -both Ethernet0/0 and line protocol are up All the link lights are on too (router...
  15. jumper4000

    Can't ping or access Ethernet interface

    Hi, I'm working on a 3640 and am trying to configure one of the interfaces with an IP address so I can upload my config file using tftp. After I configured the interface, i connected it to a little 4 port switch and connected my computer to the switch as well. However, when I try to ping the...
See more

Part and Inventory Search

Back
Top