Recent content by jtrice

Bcastner, Is there a way to format the text in the Notice Dialog Box? I am currently using a WinLogon message, but management has asked for the message to appear "Bigger" and they want to "Bold" some parts of the text. Thanks, Jim Trice

I am assuming that your Backup server is Novell and your Primary is NT at this point. Did you install the Agent software on the Primary server and configure it? Jim

Cbrider, Still awaiting the arrival of new tapes. One of the reasons I wanted to recycle some of the old tapes from the NT based backups is my new tapes had not arrived as of yet. I am pretty sure that new unused tapes will work fine. I'll let you know once they arrive. Thanks, Jim

The tapes I am trying to use have been used by Arcserve 2000 utilizing the same brand and model Autoloader with the same brand and model Tape drive. The only difference between these 2 systems is that one group of tapes has been formatted and used by Arcserve 2000, the other by Arcserve 9 for...

I am using an Exabyte EX17A with AIT2 tapes manufactured by Sony, Model SDX2-50C. I have checked the write protect on the tapes themselves and they are set to Record. These tapes both work fine in the Autolaoder designated for the Arcserve 2000 backups, I just can't seem to be able to...

I am running Arcserve 9 for Netware on Novell 5.1 SP5. I also have an instance of Arcserve 2000 for Windows running independantly. I need to use some of the old tapes from the Windows 2000 system to complete my set for Netware. However the tapes are marked as Write Protected. I have tried...

No luck with the registry key. I noticed no difference. Thanks for the input. Jim

TheLad, Thanks for the response. I am currently running IE 6.0, the workstation does have entries for the server in the Hosts file, and for the server being set to default it is the only server I have in the list and is set to default. I have also tried using the server IP address to no...

I recently installed Novell SP 5 on my 5.1 server and everything continued to run smoothly until I tried to use the Arcserve 7 manager to check on the status of some backups I had running. The manager began acting like it could not find an instance of Arcserve running on the server, however it...

Vadimh, Did you ever resolve this problem? I am experiencing the same problems and can't seem to figure it out. Please let me know if you came up with a solution. Thanks, Jim Trice

We did power-cycle the printers, but it did not seem to help. However the problem has been greatly reduced overnight. The majority of users are printing ok today with only a few users still having difficulty. Could this have been a case where we just needed to wait it out while the NDS...

We had 2 of our Novell 5.1 servers crash today. I had to force reboot them to get them back up. Once they came back up, both of them went into Vrepair. And eventually came back up. Ran DSREPAIR on both of them to clean up an misc problems asscoiated with the crash. The onlt residual problem...

Is there a way to search all messages in the GroupWise system (version 5.5) for specific text? I know it can be done from the individual users, but I need to scan over several users and thought it would be easier to scan the entire system. Novell_5.1 server, Groupwise 5.5 Thanks, Jim

I have InoculateIT 6.0 installed on a Win2000 server with a variety of different clients. I have been able to add Win98, WinXP, Win2000 server, and WinNT 40 servers to various user defined groups. I am having a hard time with assigining a WinNT 40 workstation to a group. I get the following...

I am testing XP Pro for installation in our office. I want to be able to set up all the PC's with a similar desktop configuration that varies from the XP Pro default setting. Here is the procedure that I followed: 1. Log on as a new user. 2. Make the configuration changes I want for all...