Recent content by joopdog

RESOLVED I found the problem within the Mitel Direct Connect (Small Business Edition 100). It had nothing to do with this. The problem was actually in the IIS 6.0 SMTP email server configuration. I had to change the Smart host settings. When I checked this folder: c:\inetpub\mailroot\Badmail...

QUESTION: We have the following system: Mitel Small Business Edition 100 Build: 22.13.4800.0 I'm logged in the Mitel Director Connect, where do I go to setup smtp settings? Especially for voicemail. Voicemail WAV files are not being sent to the end user. I'm using on-premise Exchange 2019. In...

Yes, they do. We have the Panasonic KX-TDE100 phone system. And the KX-NT343 phones. Everything works great.

OK I used the command. config t int f0/19 switchport trunk encapsulation dot1q switchport mode trunk switchport nonegotiate mls qos trust cos auto qos voip trust exit Cisco3550#sh int f0/19 sw Name: Fa0/19 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative...

What about the use of... switchport nonegotiate Any problems using this command? Will this help improve voice network? Any help would be appreciated. Thanks

Sh run interface FastEthernet0/16 description New Panasonic Phone System switchport access vlan 11 switchport mode access mls qos trust cos auto qos voip trust wrr-queue bandwidth 10 20 70 1 wrr-queue min-reserve 1 5 wrr-queue min-reserve 2 6 wrr-queue min-reserve 3 7 wrr-queue...

Ok. Thanks.

We've just installed a new IP phone system (Panasonic) I created a new VLAN, VLAN 11. The subnet is 192.168.11.0/24. I created the Vlan on our Cisco 3550 switch. ! Cisco 3550 - Vlan on Ports 16, 17, 18 config t int range f0/16 - 18 description New Panasonic Phone System switchport access vlan...

Not familiar with the Cisco SRW2024P switch. However, we two Cisco SLM224P switches. I have a main Cisco 3550 switch in one building. And in the two other buildings I have two SLM224P switches. IT WORKS GREAT!!! It took me sometime, but I got it to work. And there's very little info out there...

Same as the above. Only using 1800 series routers instead of the 2514 routers. I'm not sure what model, however, I'm looking at the 1841, a modular platform unit, with three T1's and ethernet ports. We're going from one building to another at a different location: 1800 Router1-->Point-To-Point...

I use the Tftpd32 TFTP Server. And it's free. http://tftpd32.jounin.net/ Download: http://tftpd32.jounin.net/tftpd32_download.html

Thanks for that. I believe within the next couple of months we are swapping our 2514 Router for 1800 series routers. Any ideas on the VLAN and Trunking configuration for the 1800 series router?

We have an old outdated phone or voice VoIP (NBX 100) system on our network. And we are using a Cisco 3550 switch. So far everything works. VLAN1 – Data VLAN2 - Data VLAN4 – Voice Cisco 3550 IOS Commands config t int vlan 4 ip address 192.168.14.10 255.255.255.0 no shut exit int range fa0/19-20...

Thanks viprergg, I tested it on a Cisco 2950 Switch that’s not in production. And it WORKED!!! I typed in the following commands: cisco2950(config-vlan)# vlan 10 cisco2950(config-vlan)# name VLAN0010 cisco2950(config)# int vlan 10 cisco2950(config-if)#ip address 10. 0.1.10 255.255.255.0...

We have an old outdated phone or voice VoIP (NBX 100) system on our network. And we are using a Cisco 3550 switch. So far everything works. However, our network is slow because of the old VoIP phone system, due to broadcasting (design flaw), I'd like to put the phone traffic on a different...