Recent content by jmcooney

Hi, I have a need to extract out the station detail from an Avaya system (migrating site to Cisco Call Manager). In the Nortel world I can run a full TNB into a text file and then run through an Excel macro and magically I have a perfect report. In the NEC world, I have to export out a bunch...

I have a Nortel CS1000 r4 w/Avaya Modular Messaging (integration is with digital set emulation). I have a situation where the light is lit indicating there is a message, but the MWI database indicates the light is off and there are no messages in the mailbox. After trying to resync the MWI and...

Can anyone recommend any good sites for information on IP Telephony? Specifically I am looking for some info on killer applications for IPT, what telephony stuff still isn't as good in IPT compared to TDM and are there any different legal ramifications for implementing IPT in different parts...

How do you know to skip the first three? Is there somewhere in the NTPs or flips that tell you this? Maybe I am supposed to skip some on the CLNG and CLED too????

I apologize in advance for the length of the data --- did not find a means of using an attachment. >ld 96 DCH000 .set msgo 63 mon 2 .enl msgo 60 .dis msgo 60 .enl DCH017 .enl msgo 63 . DTC001 DCH 63 OMSG SETUP REF 00000017 CH 18 23 TOD 8:43:38 CK 0E89C546 HEADER:01 01 00 36 08 01...

Hmm I assumed the DISP would have converted out to the name (as it was the only difference between the PRI sending name and the one not). I have more output, but only put in two different call set ups. What IE would represent the name? As far as the Hex to ASCII, even with the link provided...

Thanks guys. Now I see something, but I am a little embarrassed to say I can not figure out the conversion (I checked the Internet for a hex to ASCII conversion table, but I am not able to figure it out -- for example -- I know the calling number is 416 something and expect to see 10 hex codes...

My previous question had to do with sending name and not wanting to, which I backed my way into an answer (changing NCNA to no from the default of yes). However, I wanted to prove this by looking at the d channel messages. Unfortunately, I do not see the name on either PRI (I expected to see...

Thanks for your response. I had already checked the RCAP -- it is ND2 on both. With regard to your second suggestion, I am looking for a little clarification: are you suggestion to enable the messaging to see if I am passing both on each and then I would know for sure the provider is...

First, I apologize that I may have sent a similar question to this one before, but I was unable to locate it when I did a search on the site. We have two PRIs that appear to be configured exactly the same on our side (as far as the route and the ADAN D-channel info are concerned). Not sure if...

It appears the LD 95 name info along with the full telephone number is being sent to the called party end when using a new PRI we installed this past week. The original PRI does not pass the name info -- only passes the telephone number. I have asked the carrier to check on this and they have...

Thanks for the first two replies. DES in the CPND block is already NO. Since both the new and old phones, both of which are of the type 3904, use the same CPND block, would it have been possible that this could be the change required if they both behave differently? Do you think I need to...

During the roll-out of an additional 70 phones (and a new PRI with new phones using the new PRI), we noticed behavior that was different from previous behavior. During testing because we had ported the numbers from one carrier to another (now both are the same), we noticed that when dialing the...

Does anyone know where I can get up to date NTPs in electronic form? A while back I was able to pull them off a site, but they were a bit out of date (they were helpful anyway, but now I do not seem to be able to access the site). This was the site, but I am not able to access it with any...

Our old Opt 11 dumb terminal just bit the dust. We have connected a PC using a very nonstandard terminal emulation package -- emulating VT220. Unfortunately because of internal software distribution issues, we can not load any other emulation software. The PBX works fine, but when going to...