Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by jm9776

  1. jm9776

    6509 and VSS

    NortonES2, I just installed a couple of 6509E's in VSS mode and cisco recommended to use VS-S720-10G-3C sup's. You may need to verify that the 6500 chassie's you have will support the new sup's and also be aware that not all blades are supported at this time. I ran into a problem where it...
  2. jm9776

    Unity Ports won't register with Call Manager

    Myarberry, Is this a new intregration with unity or has the system been up and running and now the ports are unregistered. If this is a new setup then verify that the port names are configured the same way as in unity. Also from unity make sure that you can reach callmanager. I ran into a...
  3. jm9776

    castelle faxpress and callmanager 6.1

    I am currently trying to connect my Castelle Faxpress 5000 to my callmanager 6.1. I have read through the documents from castelle which really do not go into depth. Currently i am connecting it to a vg224 (setup as sccp in callmanager) and wanted to see if any knows what the fxs port settings...
  4. jm9776

    comcast digital voice connected to h323 fxo port

    I wanted to check and see if and would know the answer to a problem i am having. I am using cm6.1.2 with 1760 as a h323 gateway. I am connecting to comcast digital voice service to my fxo card. I am finding that i can only get 1 out of 3 calls in from the outside (FXO card LED only lites on...
  5. jm9776

    callmanager 4.1 7936 problems

    Thank you all for your help. I ended up just assigning static ip addresses and TFTP ip's on each phone. Once this was done they registered right away.
  6. jm9776

    callmanager 4.1 7936 problems

    That is correct. They have been disconnected from the network and power supply. The strange thing is all of the 7940's and 60's have not had a problem. DHCP is up and running also is the TFTP service from callmanager.
  7. jm9776

    callmanager 4.1 7936 problems

    I have a callmanager 4.1 and had a network down issue this week. Since this time the 7936 conf phones have not registerd back to callmanager. Currently they are stuck on configuring ip address. I have checked the DHCP server for the mac addresses of the phones and clear out any leases that...
  8. jm9776

    Setup VOIP Phone

    Undertaker48, Here is a guide for the administration portion of the callmanger. It is for a different relase but will work for you. Let me look around and see what i can find for phone setup. Here is the book that you should look into getting which will help guide you with configurations...
  9. jm9776

    cme 4.1 trunk group on 4fxo

    Thank you Jeter and whykap for your help. My biggest worry is with a line problem on one of the Fxo's. I will try adding this command to my voice ports. Thanks again!!!!!
  10. jm9776

    Setup VOIP Phone

    There are a couple things they we need to know to better point you in the right direction. What version of cisco callmanager are you running and which model phones are you using. The major difference between versions is the way the interface works. Here is a link which contains guides for the...
  11. jm9776

    cme 4.1 trunk group on 4fxo

    I running a cme 4.1 and have a question about trunk groups. I am using four pots lines in a 4-fxo and assigned them to a trunk group. I have the outbound dial-peers setup with the trunk group command. If i disconnect the first pots line from fxo-0 and try to place a call I get a busy signal...
  12. jm9776

    callmanger 6 install on generic pc

    I just installed CM 6.0 on a custum white box with vmware. I found through a couple of trials that you need to set it up a certian way. Here are the settings: 1. Choose custom machine 2. Linux red hat enterprise 3 3. 1 processor 4. allocate 2096mb of ram 5. bridged network connection 6. SCSI...
  13. jm9776

    callmanger 6 install on generic pc

    I am looking to see if anyone has installed cm 6.0 on a generic pc. I am looking to install it to test it in a lab enviroment. I have done it in the past with version 4. Any help would be great. Thanks!!!
  14. jm9776

    cisco wireless controller having dhcp problems across vlans.

    I have job of setting up a cisco 4400 wireless controller on our network. The network consist of cisco 3750 gig switches performing the layer 3 routing. I have a dl320 as the DC giving out dns and dhcp for two networks( w/dns entry for controller). the data network is x.x.10.0 and the wireless...
  15. jm9776

    question on how to migrate to new DID's in callmanager

    I am new to administrating changes in callmanger 4.1 and have recently given a new block of DID's to change all my users to. The old block was xxx.xxx.5000 numbers and the new block is in the 7000 range. I tried to line up the DN's to have the last two digits the same but not all line up. How...
See more

Part and Inventory Search

Back
Top