Recent content by Jimtron26

Thank you for your reply! Appreciated! The 'office' in question is actually the MD's home! So only 2 or 3 PCs and a couple of IP hardphones will be connecting through it. I'll take a look at the Sonicwalls Thanks again!

Hi all, Does anyone know any none-Cisco routers which are compatible with a Cisco 1841 for a router-to-router IPsec VPN tunnel? I've had a look at the Cisco 887's but they are a over the budget I have for the project! Many thanks in advance Jim

OK, I have determined db2admin is a valid user however still not sure what the other 4 are I have disabled the accounts to see what complains but if anyone can say what they are would be great :o)

Hi all, I have found the following User accounts in one of our Windows 2003 Servers... Start > Administrative Tools > Computer Management > Local Users and Groups > Users com db2admin newnew100 sys sysadmin These appear alongside accounts I have created and the obvious defaults eg...

Hi unclerice, thank you for your response The reason in this instance for changing the DG is for testing purposes. There is an ADSL connection on both of the routers, to test incoming web etc on the .253 router, then I can get out on the ADSL connected to the .254 router and back in again, as...

Hi all, I have two routers on a network. Each router is configured for router-on-a-stick inter VLAN-routing. VLAN 1 192.168.42.0/24 VLAN 2 192.168.43.0/24 HSRP is active between the two routers which are addressed in each VLAN as follows R1 fa 0/0 MAC 11-11-11-11-11-11 fa0/0.1 IP...

Nope... clock rate command not supported on ADSL HWIC.... http://www.cisco.com/en/US/docs/ios/12_4t/12_4t11/dsl_hwic.html

Thanks for the reply burtsbees, unfortunately, my router does not seem to have the clock rate command under the ATM interface?! Had a look through a few other forums where people have had the same problem and this does appear to have cleared it for them!

Hi Unclerico, yes I am. The ISP say they are seeing the connection between 15/17Mb downstream and the router sh dsl int command is showing the same however, when I run a speed test it is showing at best 6Mb and at worst 3Mb download. I am thinking I am missing something on the router...

Nope, still no change. Router trained at 17Mb it says from the sh dsl int atm 0/0/0 but still only getting 6Mb on speed tests. Any ideas? Cheers Jim

Hi viconsul, Yeah I have spotted that, it`s just that when I run a speed test it comes back as 8Mbps. Odd. Our provider has emailed me today however, and said they have moved us to a "Gold" service and now showing at 15Mb! ISP`s eh? Anyway will run speed tests and post if still the same...

Hi all, Wondering if anyone can help. I have recently been asked to upgrade our companies ADSL service from ADSL Max to ADSL 2+. To do this I have bought and installed an ADSL HWIC and upgraded the 1841 to (C1841-ADVSECURITYK9-M), Version 12.4(24)T which I was told was required for the service...

Thanks dberg35! "Any WiFi compliant Access Points" - I am guessing this should cover Cisco then!! Many thanks Jim

Hello all, I am looking at implementing PublicIP`s ZoneCD as a wireless controller for a hotspot I am installing. The two Access Points I am looking at are Cisco Aironet LWAPP 1131 Access Points. I cannot seem to find any kind of compatibility chart with details of what ZoneCD supports and...

With refernence to the last problem highlighted - no multicast BLF on local network, I have found the following statement in a Cisco Press BCMSN book.... "When a router configured for PIM-DM receives a multicast packet, the router performs the RPF check to validate the correct interface for the...