Recent content by jifitz

UPDATE: UTC 12/07/2012 15:43:31.496 Alert Intrusion Prevention IP spoof dropped 172.20.0.x, 53, X4, DC 172.20.0.Me, 65213, X1 MAC address: 00:23:54..... Ok now I know what is causing the problem. IDS. New problem. Although I can see IDS/IPS popping up in the log like this. Our subscription...

I will try to give as much detail as I can. We recently had the need to subnet our little network for ADFS and best practices which is great. I basically followed the suggestions here and built mine similar. http://www.brandontek.com/networking/sonicwall-on-a-stick Once I had set things up it...

I am helping work on a customer machine that has an Asus MB x58 and a RockRAID 2760a card. Before the RAID card was installed everything was build using one HDD. Then the card was added. Then the one drive was imaged and restored on onto the new RAID array. As an option when building the image...

I have created different subnets and assigned them to different interfaces but I can still get to each subnet no matter what it may be, A B or C. I want subnet A not to be able get to subnet B. Accept for certain shared resources in common. Example X3 192.168.1.0 X4 192.168.2.0 X5 192.168.3.0...

Not want I wanted to hear but at least I got my answer. Thanks :)

I am getting ready to study for MS tests and would like to have a lab. All of my test machines are only 32 bit. I cannot find any 32 bit eval versions that are not virtual or 64 bit. Any links that I am missing. Would greatly appreciate it.

I dropped the set prior to the command and I am good and done. It is all about syntax. Thanks. Problem solved.

Thanks for the folow up. Here is what I get when I try, let me know where I am going wrong: rommon 4 > set TFTP_CHECKSUM=0 usage: set rommon 5 > set IP_SUBNET_MASK=255.255.255.0 usage: set rommon 6 > set DEFAULT_GATEWAY=192,168.1.1 usage: set rommon 7 > set TFTP_SERVER=192.168.1.104 usage: set...

Hereis what I get when I attempt to load a variable using the set command in rommon: rommon 2 > set IP_ADDRESS=192.168.1.254 usage: set rommon 3 > set PS1=rommon ! > TFTP_CHECKSUM=1 BSI=0 SAVE_2_RTS=21:27:34 UTC Tue Jul 15 2008 RET_2_RTS=22:05:35 UTC Tue Jul 15 2008 RET_2_RCALTS= ?=1 I could be...

I am really new at Cisco, not at IT. I got a 1751 for training for the CCNA test. Ran the copy running-config startup-config command. The next thing I saw was eeeeeeee accross the screen. Then I got this "loadprog: bad file magic number: 0x0 boot: cannot load "flash:". I figured out that...

Thank you again for your advice. We already have them setup thru a VPN service that is not very friendly to VOIP. We are also using the 729 codec. I was trying to go around our current VPN. They use SSL I would rather have IPSec. MPLS would also help. We do not have the same issues in our 3 corp...

Thank you both for your answers. Prior to me coming to my company they invested in a budget VPN solution and now we are paying for it. I want an MPLS network but that I will not get.

I have a 2 BCM400s and a CS1000. I would like to to try to configure the boxes from the outside. Right now we are sending our remote VOIP traffic over VPNs that are having many issues including own way voice, and dropped calls. I wan to put a Sonicwall PRO1260 in front of it and open ports to...

Thanks for telling me what my Nortel rep missed. So a VPN is the best way?

I have a 2 BCM400s and a CS1000. I would like to to try to configure the boxes from the outside. Right now we are sending our remote VOIP traffic over VPNs that are having many issues including own way voice, and dropped calls. I wan to put a Sonicwall PRO1260 in front of it and open ports to...