Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by JesusMC

  1. JesusMC

    Setup DHCP on Novell OES for Avaya 5610 phones

    The switch the server is connected to is a HP Procurve. There are 3 vlans DEFAULT_VLAN, Data and Voice. The server is "untagged" on DEFAULT_VLAN and set to "No" for both Data and Voice. I will do. I posted here first because I thought I remembered seeing a post where someone said that had...
  2. JesusMC

    Setup DHCP on Novell OES for Avaya 5610 phones

    DHCP works fine when I use my Win2k3 server. I have a cisco 2600 router pointing the server (ip helper-address 10.1.10.x) I didn't know you could use the ip500 as the file server. I'm going to try to add that option on my Win2k3 server that is working and see if it works there. Tired of phones...
  3. JesusMC

    Setup DHCP on Novell OES for Avaya 5610 phones

    I don't have a file server so I left the TFTPsrvr=x.x.x.x out but I did take out L2Q=1,L2QVLAN=102 and the phone still froze. And by freezing I mean the lights stopped flashing and DHCP: 4 secs VLAN ID=102 was stuck on the screen. Have to unplug and replug to get it to reboot. Is there...
  4. JesusMC

    Setup DHCP on Novell OES for Avaya 5610 phones

    I'm trying to setup DHCP on a Novell OES Linux server and can't seem to get the phones working. The phones will boot and get an IP for the data vlan. Then it will reboot and freeze/lock up on DHCP. My network is as follows: 10.10.1.x(vlan=101) = data 10.10.2.x(vlan=102) = voice 10.1.10.x =...
  5. JesusMC

    1 IP500, 2 Subnets can't connect with 2nd

    There's not a good way for me to display my config. At least that I can find. Jesus*MC*
  6. JesusMC

    1 IP500, 2 Subnets can't connect with 2nd

    Right now, in the WG system manager, for testing purposes, I have a dynamic route setup to allow all traffic from the secondary network to the primary network. That should be enough, correct? Jesus*MC*
  7. JesusMC

    1 IP500, 2 Subnets can't connect with 2nd

    I'll change it back later tonight, when all the customer service reps have gone home, and let you know how it goes. Jesus*MC*
  8. JesusMC

    1 IP500, 2 Subnets can't connect with 2nd

    It was originally 255.255.0.0 but I recently changed it to 255.0.0.0 to try to make it work. Jesus*MC*
  9. JesusMC

    1 IP500, 2 Subnets can't connect with 2nd

    Yes, the IPO is at 10.1.42.1 and is on LAN 1 not WAN/LAN2. The router is setup as you have listed. The IPO was setup as you listed when it was installed and is still set that way. But with that setup, the phones on the secondary network cannot find the IPO. They can find the voicemail server...
  10. JesusMC

    1 IP500, 2 Subnets can't connect with 2nd

    OK, I guess I don't know my network terminology very well. I should have made my topic "1 IPO and 2 Networks" Yes, my router is at 10.1.10.1 for my primary network. I'd like to have a second network (not subnet) use the IPO. Is that possible? Jesus*MC*
  11. JesusMC

    1 IP500, 2 Subnets can't connect with 2nd

    I inherited the network with it just as you laid out 10.1.xxx.xxx / 255.255.0.0. But since I've been here, I purchased a new firewall. When I put it in I kept everything the same. But there are 4 ports on this UTM. Eth0 is the external and Eth1 is the 10.1.xxx.xxx network. For the new...
  12. JesusMC

    1 IP500, 2 Subnets can't connect with 2nd

    I have 2 subnets: 10.1.xxx.xxx/16 and 10.2.xxx.xxx/16 The 10.1.xxx.xxx is the main network while 10.2.xxx.xxx is another department that I want to keep out of the primary network. I only have one IPO which is on the primary. So, with that said, I'm trying to ping the IPO (which is set to...
  13. JesusMC

    1 IP500, 2 Subnets can't connect with 2nd

    I changed the default route's gateway to 10.1.42.3 but I still can't ping the IPO on 10.1.42.1 from 10.2.10.144. When I do ping, I get the 2 following messages repeated: Reply from 10.2.10.1: Destination host unreachable. Request timed out. Also, not sure if this matters, RIP is set to None...
  14. JesusMC

    1 IP500, 2 Subnets can't connect with 2nd

    I have one route set like this: IP address - 0.0.0.0 IP Mask - 0.0.0.0 Gateway - 10.1.10.1 Destination - LAN1 Metric - 0 Jesus*MC*
  15. JesusMC

    1 IP500, 2 Subnets can't connect with 2nd

    I have an IP500 system with 5610SW phones. I have a Watchguard Firebox with 4 ports. One set for external and the 3 internal are set for different subnets. (10.1.xxx.xxx, 10.2.xxx.xxx, 10.3.xxx.xxx) The IP500 is statically set to 10.1.42.1/255.0.0.0 on the primary subnet. The voicemail server...
See more

Part and Inventory Search

Back
Top