Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by jertson

  1. jertson

    caller's list on the ip phone not working

    i program a cpnd block and the caller's list is working, thanks for the support, i appreciate.
  2. jertson

    caller's list on the ip phone not working

    yes, the one that is acting as a leader....
  3. jertson

    caller's list on the ip phone not working

    i have a problem in my system, CS1000E Rls. 5.50J, with CPPM hardware, one is working as Call Server and the other as Signaling Server, on my IP Phones, i have a caller's list key, but when i press the key it says, caller's list is empty, but i just called that phone just to check if it will...
  4. jertson

    what is erl?

    when i'm programming for a new ip telephone, i passed on this prompts erl, when i put the value 1 and enter, it gives me error, it says, you have to enable the ERL, what does this mean, any idea where to enable this....the error was SCH1680, it says enable the ERL..... please help....
  5. jertson

    membership in the security domain

    if i unregister in the ucm, i can use, user name admin1, then the admin1 password, once it register in the ucm, i have to use the admin, and the admin password... going back to mgc command line, when i used the user name, pdt2, then the pdt2 password, i was able to login, but when i used the...
  6. jertson

    membership in the security domain

    i try to go to mgc command line but it's asking me a user name on user name, i enter admin2, then put my admin2 password, but say's invalid what should i enter on user name... please help....
  7. jertson

    E164 .....

    i have just activated a link between CS1000E Rls. 6.0 and Cisco Router 3825. Call Server and Signaling Server are link via sip trunks. Created steering codes for Nortel side and created routing points on the NRS side, also created gateway endpoints, domain.... i find this E164 international...
  8. jertson

    membership in the security domain

    ip 137.135.128.10 is the elan ip of my mgc card i use the command reg u s in ld 117.... i will try to use the command joinSecDomain in my mgc card...
  9. jertson

    membership in the security domain

    i just upgraded one system from CS1000M chasis Rls. 4.50W to CS1000E Rls. 7.50Q, everything was working fine, but i have few questions. when i try to register in the security domain via ld 117, it gives this error, SEC102 Element 137.135.128.10 failed to request membership in the security...
  10. jertson

    CallPilot Rls. 5.0041 Password Reset

    well, then how do i get this distributor password....
  11. jertson

    CallPilot Rls. 5.0041 Password Reset

    is the distributor password the same as callpilot rls. 4, because for callpilot rls. 4.0, i know the distributor password....
  12. jertson

    CallPilot Rls. 5.0041 Password Reset

    yes, this is the 000000/login password...
  13. jertson

    CallPilot Rls. 5.0041 Password Reset

    how do i reset the password for the callpilot. callpilot version is 5.00.41 please help....
  14. jertson

    working on nrs routing tables

    how do i assigned prefix on nrs if i have the following scenario from provider.... my vendor assigned for me 02 65352xx and 02 65353xx as my did range for my rdb programming, my acod is 76.... please help.... jertson
  15. jertson

    sip between nortel rls. 6.0 and cisco router

    after making changes in the element manager, it says that you have to restart application, after doing so, my d-channel is est now, but still i don't receive a call coming from my provider... when i check the status of my elan, it does not have an ip, and says down disable... the scenario is...
See more

Part and Inventory Search

Back
Top